Redmond RMC-M800S-E Manual Del Usuario página 8

5. From the list of available appliances select the one to be connected. The name of the appliance is the same as the model
number. You can set a new name or stop installation by default.
6. Confirm the connection of the selected appliance and follow the instructions on the screen of the mobile device. While
it is connecting, the alternating symbols
To provide stable connection the mobile device should be located within no more than 15 metres from the appliance.
Appliance control via the wireless network. Instruction on the R4S Gateway application installation is available through the link: http://
redmond.company/APP_manual_appgateway
Control panel lock
The REDMOND RMC-M800S-E multicooker is equipped with a control panel lock function to prevent misuse («child lock»).
Press and hold the button till an audible signal is heard to enable the lock. The button LED is lit up solid, and other buttons
will go out. You can enable this function at any time: while your multicooker is in the Standby mode, while selecting a pro-
gramme, or after a cooking cycle is started.
To unlock the control panel, press and hold the
Non-volatile memory
The REDMOND RMC-M800S-E multicooker has a non-volatile memory. If short power cuts occur the appliance saves all
settings to the memory. The appliance will start operation on the interrupted stage.
In case of long-term power cuts when continuation of cooking process is impossible or unwanted, unplug the appliance. To
reset the programme at next switch-on, press and hold the «Keep warm/Cancel» button until the «– – – –» message will be
lit on the display.
Time Delay function
The Time Delay function allows to adjust the time by which the dish will be ready (programme operation time included). You
may delay the programme for up to 24 hours with 5 minute intervals.
Please note that the time of delay must exceed the cooking time. Otherwise the cooking programme will start after you press
the «Start/Reheat» button.
To adjust Time Delay (not applicable for the «MULTICOOK» programme):
1. Select a cooking programme by pressing the «Menu» button.
2. Press the «Timer/Time Delay» button, adjust the cooking time if necessary. Press the «Timer/Time Delay» button again.
The «Time Delay» indicator and the remaining cooking time (time of delay start included) will be displayed.
3. Press the «–» and «+» buttons to increase or reduce the cooking time. Press and hold the corresponding button to scroll
through the digits.
To get information concerning time adjustment for the «MULTICOOK» programme please refer to the corresponding section below.
The Time Delay function is not applicable for the «FRY» and «PASTA» programmes.
When adjusting Time Delay, please note that the «STEAM» programme countdown begins only upon reaching the operating
temperature (after water comes to a boil).
Avoid using the «Time Delay» function for dairy and other perishable food.
Keep Warm function
The function automatically activates at the end of a cooking cycle (not applicable for the «YOGURT» programme) and keeps
food warm at 70-75°С for up to 24 hours. If Keep Warm is activated, the «Keep Warm/Cancel» button LED is lit up solid, and
the timer begins to count the operating time.
To disable the function, press and hold the «Keep Warm/Cancel» button.
To disable the Keep Warm function in advance press and hold the «Start/Reheat» button until the Keep Warm/Cancel» button LED
goes out. To enable the function, press and hold the «Start/Reheat» button (the «Keep Warm/Cancel» button LED is lit up solid).
General operating procedure for automatic programmes (except for the «MULTICOOK» and «REHEAT»
programmes)
For information on the «MULTICOOK» and «REHEAT» programmes please refer to the corresponding sections.
8
and will be shown on the multicooker's display.
button until an audible signal is heard. The button LED will go out.
1. Prepare (measure) the ingredients, put them into the bowl. Please make sure that all the ingredients (water included)
are below the maximum fill mark on the inside of the bowl.
2. Place the bowl inside the appliance. Make sure it makes full contact with the heating element.
3. Press the multicooker lid until it clicks into place. Plug in the appliance.
4. By pressing the «Menu» button select the required cooking programme, a corresponding programme indicator and
default cooking time will be displayed. By pressing the «Select product» button, select the type of product for the «FRY»,
«STEW», and «STEAM» programmes: a corresponding indicator («MEAT», «FISH», or «VEGETABLES») and default cooking
time will be displayed. You can adjust the cooking time.
5. Enable the «Time Delay» function if necessary.
6. Press and hold the «Start/Reheat» button for a few seconds. The «Start/Reheat» and «Keep warm/Cancel» buttons LEDs
are lit up solid. The cooking cycle starts, the timer starts to countdown.
7. You can disable the Keep warm function in advance during a cooking cycle by pressing and holding the «Start/Reheat»
button (the «Keep warm/Cancel» button LED is off). To enable the function, press and hold the «Start/Reheat» button
again.
8. When the cooking cycle is completed, an audible signal is heard. After that, depending on the settings, the appliance
switches to either the Keep Warm mode (the Keep Warm timer will count up) or to the Standby mode.
9. To interrupt the cooking cycle, to cancel the programme or to disable the «Keep Warm» function, press and hold the
«Keep Warm/Cancel» button.
To adjust the cooking time:
1. Having selected the cooking programme, press the «Timer/Time Delay» button. The «Timer» indicator is displayed, time
digits start flashing.
2. Pressing the «+» and «–» buttons, adjust the desired time value. Hold the corresponding button to scroll through the
digits.
3. After adjusting the cooking time (time digits are flashing), proceed to the next step. To clear time settings, press the
«Keep Warm/Cancel» button and start the adjustment from the beginning.
When adjusting the cooking time manually, please note that adjustment range and intervals depend on the selected programme.
In some programmes countdown begins only upon your multicooker reaches the set operation temperature.
«MULTICOOK» programme
The programme is recommended for cooking any meal with your own temperature and time settings. Temperature can be
adjusted between 35 and 170°С with 5°С intervals, and time — between 2 minutes and 15 hours with 1 minute intervals (for
up to 1 hour period of time) or 10 minute intervals (for more than 1 hour period of time).
If the cooking temperature in the «MULTICOOK» programme is below 75°С, the «Keep Warm» function is not available.
1. Follow steps 1-3 of the «General operating procedure for automatic programmes» section.
2. Press the «Multicook/°С» button, the cooking temperature will be displayed (default temperature is 100°С). Press the
«–» and «+» buttons to adjust the cooking temperature.
3. In 2-3 seconds after temperature is adjusted, the «Timer» indicator and flashing time digits will be displayed (default
time is 30 minutes).
If you failed to adjust the desired cooking temperature, press and hold the «Keep Warm/Cancel» button until an audible signal
is heard, then start the adjustment from the beginning.
4. Press the «–» and «+» buttons to adjust the cooking time. Press and hold the corresponding button to scroll through
the digits.
5. To set the time of delay (if necessary), press and hold the «Timer/Time delay» button. The «Time delay» indicator and
the remaining cooking time (time delay included) are displayed. Adjust the time value by pressing the «–» and «+»
buttons. Press and hold the corresponding button to scroll through the digits.
6. Then follow steps 6-8 of the «General operating procedure for automatic programmes» section.
«RICE/GRAIN» programme
The programme is recommended for cooking rice and other types of grain. Default cooking time is 35 minutes. You can
manually adjust the cooking time from 5 minutes to 4 hours in 1 minute intervals.