Husky HDS550 Manual De Instrucciones Y Lista De Piezas página 2

Operating Instructions and Parts Manual
Detail Spray Gun
Spray Gun Terms
FlUID cOnTrOl knOB – Used to con-
trol the amount of paint being mixed
with air.
PaInT Tank – An auxiliary pressurized
paint reservoir that allows continuous
spraying of large amounts of paint with-
out stopping for refills as with a canister.
It also allows using the spray gun at any
angle or orientation.
General Safety
Information
calIFOrnIa PrOPOSITIOn 65
You can create dust
when you cut, sand, drill
or grind materials such
as wood, paint, metal, concrete,
cement, or other masonry. This
dust often contains chemicals
known to cause cancer, birth
defects, or other reproductive
harm. wear protective gear.
This product or
its power cord
may contain chemicals known to
the State of california to cause
cancer and birth defects or other
reproductive harm. wash hands
after handling.
General SaFeTy InFOrMaTIOn
1. Read all manuals included
with this product carefully.
Be thoroughly familiar
with the controls and the
proper use of the equip-
ment.
2. Follow all local electrical and safety
codes as well as in the United States,
the National Electrical Codes (NEC)
and Occupational Safety and Health
Act (OSHA).
use a face mask/respirator
and protective clothing
when spraying. Always
spray in a well ventilated area to
prevent health and fire hazards.
Refer to Material Safety Data
(cont.)
Sheets (MSDS) of spray material
for details.
Never spray closer
than 25 feet to the
compressor! if possible,
locate compressor in separate
room. Never spray into the
compressor, compressor controls or
the motor.
3. Do not smoke or eat when spraying
paint, insecticides, or other flam-
mable substances.
Do not spray flammable
materials in vicinity
of open flame or near
ignition sources. Motors, electrical
equipment and controls can cause
electrical arcs that will ignite a
flammable gas or vapor. Never store
flammable liquids or gases in the
vicinity of the compressor.
4. When spraying and cleaning, always
follow the instructions and safety
precautions provided by the material
manufacturer (Refer to MSDS).
materials, toxic chemicals,
fertilizers or pesticides. using
these materials could result in
death or serious injury.
5. Keep visitors away and NEVER allow
children or pets in the work area.
MANUEL
yourself or anyone else or serious
injury could occur.
6. Always work in a clean environment.
To avoid injury and damage to the
workpiece, do not aim the spray gun
at any dust or debris.
Do not use pressure that
exceeds the operating
pressure of any of the
parts (hoses, fittings, etc.) in the
painting system.
objects. Bursting air hoses may
cause injury. Examine air hoses
regularly and replace if damaged.
7. Always use a pressure regulator on
appropriate water/oil removal
equipment may result in damage
to machinery or workpiece.
Preparation
1. Thoroughly mix the paint in accor-
dance with the manufacturer's
instructions, adding thinner where
necessary. Most materials will spray
readily if thinned properly. Strain
material through cheese cloth or a
paint strainer. Test the consistency of
the material by making a few strokes
on a cardboard target. If material still
appears too thick, add a small amount
of thinner. THIN WITH CARE!!
2. Fill the canister about 3/4 full and
start the air compressor.
3. Set up a piece of cardboard or other
scrap material to use as a target and
adjust for best spray pattern.
Do not spray
acids, corrosive
Air Cap
Lock Ring
Never aim or
spray at
Figure 1
Fan DIrecTIOn
The direction of the fan (horizontal or
vertical) can be changed by loosening
the lock ring and turning the air cap 90
degrees (See Figure 1). Hand tighten
lock ring after adjustment.
2
HDS550
Keep hose away
from sharp
the air supply to the spray gun.
Failure to
install
Horizontal Fan
Vertical Fan