Additional Functions - Toshiba TOSVERT VF-S15 Serie Manual De Inicio Rápido

Main circuit power supply Main circuit power supply
three-phase 200-240V three-phase 200-240V
-50/60Hz -50/60Hz
single-phase 200-240V single-phase 200-240V
-50/60Hz -50/60Hz
three-phase 380-500V three-phase 380-500V
-50/60Hz -50/60Hz
Single Single MCCB(2P) MCCB(2P)
phase phase
R/L1 R/L1
Power Power
S/L2/N S/L2/N
supply supply
*1: The T/L3 terminal is not provided for *1: The T/L3 terminal is not provided for
single-phase models. single-phase models.
Use the R/L1 and S/L2/N terminals as Use the R/L1 and S/L2/N terminals as
input terminals. input terminals.
*2: The inverter is supplied with the PO *2: The inverter is supplied with the PO
and the PA/+ terminals shorted by and the PA/+ terminals shorted by
means of a shorting bar. means of a shorting bar.
Before installing the DC reactor (DCL), Before installing the DC reactor (DCL),
remove the bar. remove the bar.
*3: When using the OUT output terminal in *3: When using the OUT output terminal in
sink logic mode, short the NO and CC sink logic mode, short the NO and CC
terminals. terminals.
*4: When VIA or VIB terminal is used as logic *4: When VIA or VIB terminal is used as logic
input terminal, refer to the instruction manual. input terminal, refer to the instruction manual.
*5: To supply control power from an external *5: To supply control power from an external
power supply for backing up the control power supply for backing up the control
power supplied from the inverter, an optional power supplied from the inverter, an optional
control power backup device (CPS002Z) is control power backup device (CPS002Z) is
required. In such a case, the backup device required. In such a case, the backup device
is used at the same time with the internal is used at the same time with the internal
power supply of the inverter. power supply of the inverter.
The optional control power backup unit can The optional control power backup unit can
be used with both 240V and 500V models. be used with both 240V and 500V models.
*6: Set the slide switch SW1 to sink side. *6: Set the slide switch SW1 to sink side.
Default setting is SINK side. Default setting is SINK side.
*7: When STO terminal is used as compliance *7: When STO terminal is used as compliance
with safety standards, refer to Safety with safety standards, refer to Safety
function manual (E6581860). function manual (E6581860).

3. Additional functions

3. Additional functions
Following functions and information are available in the model. Following functions and information are available in the model.
[Output terminal functions] [Output terminal functions]
Function No. Function No. Code Code
152 152 STO STO
153 153 STON STON
[Trip information] [Trip information]
Error code Error code Failure code Failure code
prf prf 003B 003B
[Alarm information] [Alarm information]
Error code Error code Problem Problem
STO STO
pra pra signal signal
OFF OFF
Standard connection diagram - SINK (Negative) (common:CC) Standard connection diagram - SINK (Negative) (common:CC)
DC reactor (DCL) DC reactor (DCL)
*2 (option) *2 (option)
*1 *1
MCCB MCCB
R/L1 R/L1
S/L2 S/L2 Noise Noise
filter filter
T/L3 T/L3
STO STO
*7 *7
Control power Control power
+SU +SU
supply supply
*5 *5
VF-S15 VF-S15
FLA FLA
FLB FLB
Protective function Protective function
activation output activation output
FLC FLC
RY RY
Low-speed Low-speed
RC RC
signal output signal output
FM FM CC CC
+ +
Meter Meter
Frequency Frequency
meter meter
(ammeter) (ammeter)
- -
1mA 1mA
(or 0(4)-20mA/0-10V) (or 0(4)-20mA/0-10V)
External potentiometer (1k-10kΩ) External potentiometer (1k-10kΩ)
(or voltage signal between VIA and CC: 0-10V) (or voltage signal between VIA and CC: 0-10V)
Function Function
Safe torque off signal Safe torque off signal
Inversion of safe torque off signal Inversion of safe torque off signal
Problem Problem
Safe torque off error Safe torque off error •Error of safe torque off circuit •Error of safe torque off circuit
The message in the table is displayed to give a warning but does not cause the inverter to trip. The message in the table is displayed to give a warning but does not cause the inverter to trip.
Possible causes Possible causes
•STO terminal is in open-circuit. •STO terminal is in open-circuit.
•Input voltage of STO terminal is •Input voltage of STO terminal is
low. low.
• P24 terminal (24Vdc power • P24 terminal (24Vdc power
output) is in overload. output) is in overload.
PC/- PC/-
P0 P0 PA/+ PA/+ PB PB
Power circuit Power circuit
Control Control
circuit circuit
RES RES
S1 S1
S2 S2
S3 S3
Operation panel Operation panel CC CC
SW1 SW1 *6 *6
P24 P24
SINK SINK SOURCE SOURCE
OUT OUT
PLC PLC
NO NO
RS485 RS485
connector connector
SW2 SW2
CC CC
S4 S4
VIB VIB
S3 S3
PTC PTC
*4 *4 *4 *4
VIC VIC
VIB VIB VIA VIA PP PP
Action Action
ON : Opening terminals between +SU and STO. ON : Opening terminals between +SU and STO.
OFF: Shorting terminals between +SU and STO. OFF: Shorting terminals between +SU and STO.
Inversion of STO Inversion of STO
Possible causes Possible causes
Remedies Remedies
•Close STO and + SU circuit. •Close STO and + SU circuit.
•Check the load of P24 terminal, if STO and +SU is •Check the load of P24 terminal, if STO and +SU is
shorted. shorted.
•Use P24 terminal within 100mA, including the transient •Use P24 terminal within 100mA, including the transient
response. response.
36 4 4
E6581965
E6581965 E6581965
Braking resistor（Option） Braking resistor（Option）
Motor Motor
U/T1 U/T1
V/T2 V/T2
M M
W/T3 W/T3
F F Forward run command Forward run command
R R Reverse run command Reverse run command
Reset Reset
Preset-speed command 1 Preset-speed command 1
Preset-speed command 2 Preset-speed command 2
Preset-speed command 3 Preset-speed command 3
Common Common
Speed reach Speed reach
signal output signal output
Ry Ry
*3 *3
Current signal: 4(0)-20mA Current signal: 4(0)-20mA
Voltage signal: 0-+10V Voltage signal: 0-+10V
(or -10-+10V) (or -10-+10V)
Remedies Remedies
•Contact your Toshiba distributor. •Contact your Toshiba distributor.