Consumer Information - Moen 4520 Guía De Instalación Y Garantía

FLUSHING INSTRUCTIONS
IMPORTANT: Pipe chips, sand, stones and other solids found in new and renovated
plumbing can damage the sealing surfaces of the cartridge and cause leaks. To avoid
damage, DO NOT TURN ON SUPPLY VALVES until instructed below:
1. After installing and connecting your new faucet, turn on in the full cold position
(handle pointing to the right) and turn on the cold supply for 15 seconds.
2. Without closing the handle, turn to the full hot position (handle pointing to the left)
and turn on the hot supply for 15 seconds.
3. Close the handle, unscrew the aerator from the end of the spout and clean the
aerator screen.
4. Replace aerator and check system for leaks.
DISASSEMBLY
1
1
4
2
3
5
1. Pry out plug button (3), remove set screw (2) and lever handle (1).
Unscrew handle screw (4) and lift off the handle adapter (5) (with handle
connector (6) attached).
2. Unscrew the pivot retainer (7).
3. Remove washer (8), collar (9) and the retainer clip (13). Lift off the stop
sleeve (10).
4. (NOTE: Check the position of the cartridge to aid proper replacement).
Using pliers, pull the cartridge (12) out of the faucet body by the stem as
shown above. Remove washer (11).
For reassembly reverse the steps above.
MOEN LIFETIME LIMITED WARRANTY
Moen products have been manufactured under the highest standards of quality and
workmanship. Moen warrants to the original consumer purchaser for as long as the original
consumer purchaser owns their home (the "Warranty Period" for homeowners), that this
faucet will be leak and drip-free during normal use and all parts and finishes of this faucet will
be free from defects in material and manufacturing workmanship. All other purchasers
(including purchasers for industrial, commercial and business use) are warranted for a period
of 5 years from the original date of purchase (the "Warranty Period" for non-homeowners).
If this faucet should ever develop a leak or drip during the Warranty Period, Moen will FREE
OF CHARGE provide the parts necessary to put the faucet back in good working condition and
will replace FREE OF CHARGE, any part or finish that proves defective in material and
manufacturing workmanship, under normal installation, use and service. Replacement parts
may be obtained by calling 1-800-289-6636 (Canada 1-800-465-6130), or by writing to the
address shown. Proof of purchase (original sales receipt) from the original consumer
purchaser must accompany all warranty claims. Defects or damage caused by the use of other
than genuine Moen parts are not covered by this warranty. This warranty is applicable only to
faucets purchased after December 1995 and shall be effective from the date of purchase as
shown on purchaser's receipt.
This warranty is extensive in that it covers replacement of all defective parts and finishes.
However, damage due to installation error, product abuse, product misuse, or use of cleaners
containing abrasives, alcohol or other organic solvents, whether performed by a contractor,
service company, or yourself, are excluded from this warranty. Moen will not be responsible
for labor charges and/or damage incurred in installation, repair or replacement, nor for any
indirect, incidental or consequential damages, losses, injury or costs of any nature relating to
this faucet. Except as provided by law, this warranty is in lieu of and excludes all other
warranties, conditions and guarantees, whether expressed or implied, statutory or otherwise,
including without restriction those of merchantability or of fitness for use.
Some states, provinces and nations do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights and you may also have other rights which vary from
state to state, province to province, nation to nation. Moen will advise you of the procedure to
follow in making warranty claims. Simply write to Moen Incorporated using the address below.
Explain the defect and include proof of purchase and your name, address, area code and
telephone number.
3
2
7
TROUBLESHOOTING
TO CORRECT REVERSED HOT AND COLD POSITIONS:
1. Position handle so that it points toward you.
"Disassembly").
2. Turn cartridge stem around so that the notch is turned one half turn or 180°.
TURN STEM
1/2 TURN
3. Re-install handle in the same position that it was in when you took it off (pointed
directly toward you). Tighten handle screw securely and replace plug button.
8
3
9
10
13
CAUTION: Be careful not to damage the rubber seals when
re-installing cartridge. During installation be sure of the following:
• Stem must be in open position
• Position ears front to back
• Notched flat on stem faces toward front of
faucet
• Retainer clip straddles ears

CONSUMER INFORMATION

Faucets made of leaded brass alloys may contribute small amounts of lead to
water that is allowed to stand in contact with the brass. The amount of lead
contributed by any faucet is highest when the faucet is new. The following steps
may reduce potential exposure to lead from faucets and other parts of the
plumbing system:
• Always run the water for a few seconds prior to use for drinking or cooking
• Use only cold water for drinking or cooking
• If you wish to flush the entire plumbing system of water that has been standing
in the pipes or other fittings, run the cold water until the temperature of the
water drops, indicating water coming from the outside main
• If you are concerned about lead in your water, have your water tested by a
certified laboratory in your area
In the U.S. call our toll free Helpline number for answers
to any product, installation, or warranty questions.
Moen Incorporated • 25300 Al Moen Drive • North Olmsted, OH 44070-8022 U.S.A.
In Canada Moen Inc. • 2816 Bristol Circle • Oakville, Ontario L6H5s7
Remove handle parts (see
NOTCHED
FLAT ON
STEM
4
12
11
EAR
NOTCH
HELPLINE:
1 (800) BUY-MOEN
[289-6636]
In Canada:
Toronto: 905-829-3400;
Rest of Canada: 1-800-465-6130
In Mexico:
(84) 88-08-26, 88-08-27,
o 91-800-84-345
CLIP