Virutex MEB50 Manual De Instrucciones página 6

Fig. 7), you will have to adjust the position of the rear
support guide (A, Fig. 7) so that the clamp exerts some
force on the outer edge of the panel, and fix the guide
in this position with the Levers (I, Fig. 1).
To edgeband panels wider than 500 mm, on which it is
not possible to use the clamp, it can easily be removed
and placed upside down so that it does not get lost.
Edgbanding:
If the PEB50/PEB150 edgebander is ready to glue edges,
as explained in section 6, follow the steps below to
edgeband the board:
Turn on the advance switch (IA, Fig. 7) located on the
handle of the machine.
Wait a few seconds for the glue to rise from the tank
to the gluing roller.
Push the edging though the guides until it reaches
the advance roller, which will transport the duly glued
edging until it exits over the pressure roller.
Push the board forward to meet the edging when it
comes out of the pressure roller.
Press the board against the edging located on the pressure
roller, so that the rotating movement of the latter sets
the board advance speed, and keep both hands on it
until the end of the edgebanding process.
Turn off the advance switch (IA, Fig. 7).
If you have finished working with the machine, turn off
the main switch (IG, Fig. 2).
8. EDGEBANDING CIRCULAR PIECES
Prior adjustments:
Lift the PEB50/PEB150 edgebander so that the glued
edging comes out flush with the worktop:
• To edgeband circular boards, place the PEB50/PEB150
edgebander in the position shown in (Fig. 2), but put
the attachments (T and U, Figs. 3, 8 and 9) under the
machine to raise it.
Place the worktop attachments in position:
• Some worktop attachments (S, Fig. 10) should be
arranged in the desired positions, so that the board is
supported while edgebanding, without the excess lower
edging hitting them when the board is moving.
Remove the support guides:
• Remove the intake and exit guides from the worktop
(M and L, Fig. 2), by loosening the screws (R, Fig. 2).
Remove the Clamp:
• When edgebanding circular boards, it is not possible
to use the clamp (F, Fig. 1). It should be removed and
placed upside down so that it does not get lost.
Edgbanding:
If the PEB50/PEB150 edgebander is ready to glue edges,
as explained in section 6, follow the steps below to
edgeband a circular board:
• Turn on the advance switch (IA, Fig. 11) located on
6
the handle of the machine.
• Wait a few seconds for the glue to rise from the tank
to the gluing Roller.
• Place the board on the worktop attachments (S. Fig.
10) and in front of the pressure roller.
• Push the edging through the guides until it reaches
the advance roller, which will transport the duly glued
edging until it exits over the pressure roller.
• Press the board against the edging located on the
pressure roller, so that the rotating movement of the
latter sets the board advance speed.
• Push the board to the second roller and edgeband the
rest of the board by moving it between the two rollers
(Fig. 11), until the edgebanding process is finished.
• Turn off the advance switch (IA, Fig. 11).
• If you have finished working with the machine, turn
off the main switch.
9. EDGBANDING SMALL PIECES WITH RADII
AND SHAPES
Make the same adjustments as for edgebanding circular
pieces, as well as:
Additional adjustments:
Remove the auxiliary pressure roller and its shaft:
• Use a screwdriver to remove the screw (P, Fig. 2) that
holds the roller in position.
• Remove the roller shaft as well, unscrewing it by
inserting a 4 mm rod in the hole.
Place the rear attachments in position:
• On some pieces it may be necessary to place some rear
attachments (V, Fig. 2, 3 and 12) at the bottom of the
board exit point and in the desired positions, so that
it is supported during edgebanding, and without the
excess edging hitting them as it advances.
Edgbanding:
If the PEB50/PEB150 edgebander is ready to glue edges,
as explained in section 6, follow the steps below to
edgeband a small board with radii and shapes:
• Turn on the advance switch (IA, Fig. 12) located on
the handle of the machine.
• Wait a few seconds for the glue to rise from the tank
to the gluing roller.
• Place the board on the worktop attachments (S, Fig.
12) and in front of the pressure roller.
• Push the edging through the guides until it reaches
the advance roller, which will transport the duly glued
edging until it exits over the pressure roller.
• Press the board against the edging located on the
pressure roller, so that the rotating movement of the
latter sets the board advance speed, keeping both
hands on it and following its shape until the end of the
edgebanding process.
• Turn off the advance switch (IA, Fig. 12).
• If you have finished working with the machine, turn