Fasteners; Troubleshooting; Corrective Action - Campbell Hausfeld NB0040 Manual De Instrucciones

Tabla de contenido

Publicidad

Operating Instructions

Fasteners

The following Campbell Hausfeld brad nails are available at local retail stores. For help locating any item, call customer ser-
vice at 1-800-543-6400. Campbell Hausfeld nails meet or exceed ASTM Standard F1667.
Model #
Length
FB001600
5/8"
FB002000
3/4"
FB002500
1"
FB003000
1-1/4"
FB004000
1-1/2"
FB004500
1-3/4"
FB005000
2"
Interchange Information
Nails used in the Campbell Hausfeld NB0040 Brad Nailer will also work in: Bostitch T31-1, T29-30, BT-35, BT50, Duofast
BB4440, Hitachi NT45A , Paslode 2138-F40 , Porter Cable BN125, BN200, Sears 18409, 18424, and Senco SLP20, LS2, LS5.
Troubleshooting Guide
Stop using nailer immediately if any of the following problems occur. Serious personal injury could
result. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service
Center.
Symptom
Air leaking at trigger valve area
Air leaking between housing
and nose
Air leaking between housing
and cap
Nailer skips driving nail
Nailer runs slow or has loss of power
Nails are jammed in nailer
Air leaking at trigger valve stem
Shank
Finish
Gauge
18 Gauge
Galvanized
18 Gauge
Galvanized
18 Gauge
Galvanized
18 Gauge
Galvanized
18 Gauge
Galvanized
18 Gauge
Galvanized
18 Gauge
Galvanized
Possible Cause(s)
O-Rings in trigger valve housing are damaged
Loose screws in housing
Damaged O-Rings
Damage to bumper
Loose screws
Worn bumper
Dirt in nose piece
Dirt or damage prevent nails or pusher from
moving freely in magazine
Damaged pusher spring
Inadequate air flow to nailer
Worn O-Ring on piston etc.
Damaged O-Ring on trigger valve
Air leaks
Cap gasket leaking
Nailer not lubricated sufficiently
Broken spring in cylinder cap
Exhaust port in cap is blocked
Guide on driver is worn
Nails are not correct size
Nails are bent
Magazine or nose screws are loose
Driver is damaged
Nails loaded incorrectly
O-Rings or seals are damaged
Head
Collation
Brad /Brown
Adhesive
Brad /Brown
Adhesive
Brad /Brown
Adhesive
Brad /Brown
Adhesive
Brad /Brown
Adhesive
Brad /Brown
Adhesive
Brad /Brown
Adhesive

Corrective Action

Replace O-Rings. Check operation of Work Contact
Element (WCE)
Tighten screws
Replace and lubricate O-rings
Replace bumper
Tighten screws
Replace bumper
Clean drive channel
Clean and check magazine
Replace spring
Check fitting, hose or compressor
Replace and lubricate O-rings
Replace and lubricate O-rings
Tighten screws and fittings
Replace gasket
Lubricate nailer
Replace Spring
Replace any damaged internal parts
Replace guide
Use only recommended nails
Replace with undamaged nails
Tighten screws
Replace driver
Review Loading/Unloading section in this manual
Replace O-Rings or seals
5
Model NB0040
Nails Per
Nails Per
Stick
Box
100
5000
100
5000
100
5000
100
5000
100
5000
100
5000
100
5000
www.campbellhausfeld.com

Publicidad

Tabla de contenido
loading

Tabla de contenido