DynaTrap DT1100 Manual Del Propietário

MODEL: DT1100
OWNER'S MANUAL
Thank you for purchasing this
DYNATRAP Insect Trap!
®
U.S. Patent No. D699,809
IMPORTANT SAFETY INSTRUCTIONS
WARNING, When using electric appliances, basic precautions should always be followed, including the following:
– To disconnect, turn all controls to the off ("O") position, then remove plug from outlet.
– Unplug from outlet when not in use and before servicing or cleaning.
– To reduce the risk of electrical shock, do not put appliance in water or other liquid.
– This appliance is provided with double insulation. Use only identical replacement parts.
– Connect only to a circuit that is protected by a ground-fault circuit-interrupter (GFCI).
See instructions for Servicing of Double-Insulated Appliances.
INSTRUCTIONS FOR DOUBLE-INSULATED, CORD-CONNECTED APPLIANCES:
In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided
on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing of a double-insulated
appliance requires extreme care and knowledge of the system, and should be done only by qualified service personnel.
Replacement parts for a double-insulated appliance must be identical to those parts in the appliance.
IMPORTANT SAFETY INSTRUCTIONS
Please read these instructions before using the DYNATRAP ® Insect Trap and keep for future reference.
1. Always turn unit off and disconnect plug before servicing, cleaning, or changing bulb.
2. Do not position the unit near heat, gas, oil or other flammable materials.
3. Mount product out of reach from children.
4. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged, or if it has been dropped into water.
5. This product is equipped with 2-conductor cord and 2-prong polarized plug as a safety feature. This plug will fit in a
polarized outlet only one way. If the plug does not fully fit in the outlet, then reverse the plug. If it still does not fit,
then contact a qualified electrician. To reduce the risk of electrical shock, only plug into a properly installed outlet.
Do not attempt to defeat this safety feature.
6. Do not insert fingers or any foreign objects into the unit while it is connected to an electrical outlet.
7. Collected insects within the unit may contribute to fire, so clean insects from the unit frequently.
8. Do not clean this product with water spray. Do not place where it can fall into water, or near flammable materials.
9. Do not touch fan while in motion.
10. Do not abuse cord—never carry or hang unit by cord or yank it to disconnect from receptacle. Keep cord away from heat,
oil, or sharp edges.
11. Use only extension cords that are clearly marked "Suitable for Use with Outdoor Appliances" and that have plug and
receptacles that match the product plug. Replace all damaged cords.
INSTALLATION & OPERATING INSTRUCTIONS
1. Unpack unit. Save carton for off-season storage (if needed).
2. If hanging or mounting the unit, place approximately 3–6 feet above the floor/ground level for optimal catch rate and
easy access for cleaning.
3. If mounting the unit to a wall, install the mounting bracket to the side of the DT1100. This bracket slides into side wall
of the DT1100.
4. Turn power switch to "ON" position (The power switch is located under the rain protector)
5. Plug cord into an outdoor outlet or UL listed extension cord as described in "IMPORTANT SAFETY INSTRUCTIONS".
6. For best catch results leave unit on at all times, except when cleaning or servicing.
7. It is recommended to place the unit 20-40 feet away from where people will be sitting.
8. Catch rate activity will be higher at night. For best catch results it is recommended to keep the unit away from competing
light sources. Intended for household use only.
CLEANING
Clean the trap at least once a week to prolong life of the unit, insure fire prevention, and provide for more efficient operation.
1. Be sure to clean the unit once per week
2. Switch the unit off and unplug before cleaning
3. For weekly cleaning, remove the screw securing the retaining cage and then twist the cage clockwise. Remove the damper
by grasping the crossbar near the edge of the damper. Pull up firmly. Remove any buildup from the inside of the retaining
cage and fan with a brush (included). Replace damper, snap firmly into place.
4. For major cleaning, remove the four screws securing the fan housing to the light housing. After removing the screws,
gently pull the fan housing away from the light housing. Using a soft brush, remove dirt and debris from the light housing.
Once the cleaning process has been completed, align the screw holes in the fan housing with the screw holes in the
lighting unit and tighten the screws to the base of the lighting unit.
IMPORTANT: When replacing the retaining cage – DO NOT press / push against the screen windows.
REPLACING BULB
The Light bulb life expectancy is approximately 3,000 hours (or about 4 months), and should be replaced regularly to ensure
optimal UV effectiveness. Even though the bulb's light may be visible to you, its ability to attract insects diminishes over time.
1. Turn power switch to "off" position. UNPLUG UNIT, and allow bulb to cool before replacing.
2. Remove the screw securing the retaining cage and then twist the cage clockwise. Turn the unit upside down.
3. Remove the four screws securing the fan housing to the light housing. After removing the screws, gently pull the fan
housing away from the light housing. Using a soft brush, remove dirt and debris from the light housing. Once the cleaning
process has been completed, untighten the screw securing the base of the light bulb to the light housing. Slide the metal
bracket to the side. Cover the bulb with a cloth to protect your finger and hand. Grasp the bulb (with your hand and fingers
protected by the cloth) and gently pull the bulb from the socket.
4. Remove any debris from the lamp socket with a brush before inserting the new bulb. Replace the metal plate over the base
of the bulb and tighten the retaining screw.
5. Align the screw holes in the fan housing with the screw holes in the lighting unit and tighten the screws to the base of
the lighting unit.
6. Replace the retaining cage at the bottom of the unit.
Replacement fluorescent bulbs can be found at your local retailer
or can be ordered directly from DYNATRAP by calling
1-877-403-TRAP (8727) or visiting www.dynatrap.com
ON/OFF SWITCH
HOW THE DYNATRAP INSECT TRAP WORKS
®
UV BULB
Flying insects are attracted to the unit by the UV light and CO that is
2
generated by the photo-catalysis between the UV lamps and the
special TiO coating. The fan then pulls the insects into the screened
2
base, trapping them until they dehydrate and die. The base can be
removed, allowing the contents to be periodically emptied into the
FAN
trash. The see-through screen shows the insects trapped in the
compartment, alerting you when the cage needs to be emptied.
RETAINING
CAGE
TROUBLESHOOTING
Problem: Possible cause:
Bulbs do not illuminate 1. No electrical power
and fan does not spin.
Bulb illuminates, but fan 1. Shorted fan
does not spin.
Fan spins, but bulb does 1. Bulb not seated
not illuminate properly
2. Burnt out bulb
LIMITED WARRANTY
DYNAMIC warranties to the original purchaser that this product is free from defective materials and
workmanship. This warranty is limited to remedy any defective part for a period of one year from date of
original date of purchase. Retain your original receipt as proof of purchase. This warranty does not apply
to the light bulb, nor to, in our judgment, misuse or abuse. If this unit has been altered, no warranty is in
force. This warranty does not apply if this unit is purchased outside the United States, Canada and Mexico.
In no case shall DYNAMIC be liable for any accidental, punitive, consequential, or any other damages of
any kind for breach of this or any other warranty, expressed or implied, whatsoever. Some states do
not allow limitation on how long an implied warranty lasts, so the above limitation or exclusion may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary
from state to state.
PARTS & ACCESSORIES AVAILABLE
PART DESCRIPTION
41050
7-Watt Replacement Fluorescent Bulb (1 piece)
41052
Fan Blade and DC Motor Ultra-Long Life Replacement
41053 Retaining Cage
41059 Wall Mount Bracket
41061 Large Capacity Net (to be used instead of the Retaining Cage, suitable for extra large catch performance)
HANGER
TiO COATED
2 Dynamic Solutions Worldwide, LLC
SURFACE
12247 W. Fairview Ave. Milwaukee, WI 53226
Phone: 414-431-2819
WALL MOUNT
Toll free: 1-877-403-TRAP (8727)
Toll free fax: 877-403-3293
Email: dynatrapinfo@dsw-llc.com
Visit us online at www.dynatrap.com
© Dynamic Solutions Worldwide, LLC
AUTOMATIC
SAVE THESE INSTRUCTIONS
DAMPER
Correction:
1. Check plug and receptacle and fuse or circuit breaker.
2. Check to make sure power is switched to the "ON"
position.
1. UNPLUG UNIT: Examine fan to see that it is free from
foreign material, dirt or build-up of dead insects. Clean unit as
in "CLEANING" section.
1. Check all sockets for proper bulb seating and alignment.
2. Replace bulb if needed following instructions under
"Replacing Bulbs".