Husky HDUFL50 Manual Del Usuario página 5

WARNING:
!
Disconnect the tool from the air source
whenever changing the foot plate.
Make sure there is no fastener in the
magazine before changing the foot plate.
Screws(E)
Foot plate(D)
ADJUST THE FRONT FOOT
The tool is equipped with an adjustable front foot,
can be adjusted for 3/4"-5/8" wood floors. This tool
is shipped out set for 3/4" wood floor.
To adjust the front foot (F):
1. Disconnect the tool from the air resource.
2. Empty the magazine completely.
3. Fire the tool into a piece of scrap wood to ensure.
There is no compressed air or fasteners left in the
tool.
Set the tool on its side to expose the two Bolts(G)
4.
and two Small Plates(H).
5. Loose these two Bolts (G) and two Small Plates
(H) to ensure move the Front Foot(F) in the range
of the Adjust Groove(I).
Adjust the proper position of the Front Foot(F)
6.
according to the actual thickness of wood floors
and then lock tightly these two Bolts(G) and two
Small Plates(H).
7. Ensure the correct front foot set for te wood floor
by firing into a scrap piece of flooring and
checking for proper fastener placement.
08
Bolts(G)
Front Foot
(F)
Small Plate
(H)
Adjust
Adjust
groove(I)
groove(I)
WARNING:
!
Disconnect the tool from the air source
whenever changing the foot plate.
Make sure there is no fastener in the
magazine before changing the foot plate.
SETTING THE AIR PRESSURE
The amount of air pressure required depends on
the size of the fasteners and the workpiece material.
Begin testing the depth of drive by driving a test nail
into the same type of workpiece material used for
the actual job.
Drive a test fastener with the air pressure set at 90-
95psi. Raise or lower the air pressure to find the
lowest setting that will perform the job with
consistent results.
OPERATING THE TOOL
⒈
Attach the tool to the air resource. Start your
compressor and check the pressure, making
sure it is set between 70-115psi. Do not exceed
the maximum115psi.
2.
Hold the Hand grip( J) securely and Press the
Foot plate(D) to the work surface. Make sure the
plate is over the astener target position. f
3. Press down hard so that the foot plate is firmly
contacting the work surface. Then, using the
mallet packed with the Tool, strike the hammer
K
cap( ) firmly to drive the fastener into work
surface. Lift the tool off the work surface. Repeat
this process until the job is completed.
When finished, make sure to store the tool in a
4.
clean, dry, safe location out of reach of children
and other unauthorized People.
WARNING:
!
Extreme caution must be used whenever
this tool is connected to an air resource. If
the tool is dropped, or if the Hammer
cap(K)is accidentally struck, then the tool
will fire a fastener, potentially causing
SERIOUS PERSONAL INJURY.
WARNING:
!
Keep your feet off the tool.
WARNING:
!
Before using the tool on a floor, test the
tool on a scrap piece of wood. Adjust the
driving depth by providing more or less air
pressure. Never exceed 115PSI.
Hand grip
(F)
Hammer Cap
(K)
WARNING:
!
An improperly functioning tool must not be
used. Do not actuate the tool unless the
tool is placed firmly against the work piece.
NOTE: Make sure the Hammer Cap on the flooring
nailer is in the up position before adding the air hose,
if not, the nailer may cycle(See below):
Hammer Cap(Up Position) Hammer Cap (Down Position)
CLEARING JAMS
Occasionally, fasteners may become jammed in
the firing mechanism of the tool, making the tool
inoperable. To remove a jammed fastener, follow
the steps below:
Disconnect the tool from air resource.
⒈
2. Empty the magazine. Make sure all fasteners are
removed.
3.
Try to fire the tool into a piece of scrap wood or
flooring to make sure that it's incapable of firing
any fasteners.
Set the tool on its side to expose the two Bolts
4.
(G) and two Small Plates(H)under the screws.
5. Removed these Nose Bolts(G) and two Small
Plate(H). Three Nose Bolts(L) can be seen after
removing the Front Foot(F).
Remove three Nose Bolts(L), slide the Driver
6.
Guide (M) out to expose the jammed fastener.
Remove jammed fastener, using plier or a
7.
screwdriver if required.
Replace the Driver Guide(M) and Nose Bolts (L)
8.
Replace the Front Foot (F), Plate (H) and bolts
9.
(G) back.
Reload the tool with fasteners, then reconnect
10.
the air resource to the tool.
11. Press the Drive guide (M) against a piece of
wood, and test fire the fasteners several times to
check for proper operation. If the tool is properly
firing, you may continue using the tool. If the tool
fails to perform properly, immediately discontinue
e
us and have the tool repaired by a qualified
service technician.
09