Blaupunkt BP5122BTO Manual Del Usuario página 6

For face sanding and removing small irregularities Medium 80, 100, 120 Grit
For finishing and fine sanding of all materials Fine 150, 180, 240, 320, 400 Grit
ATTACHING THE STARLOCK ADAPTOR
The tool comes supplied with an adaptor that will accept any star lock multitool blade. Please note this does not include star lock
plus or star lock max accessories.
Before attaching the star lock adaptor make sure the quick release lever is in the closed position, Fig.7.
Place the tool upside down on a free surface.
Place the inner flange of the adaptor over the accessory bolt so the two raised protrusions of the flange fit in the cutout sections
of the accessory bolt, Fig.8.
Place the star lock blade so that the raised nubs of the inner flange fit in the holes in the star lock accessory, insert the holding
flange over the blade so it fits correctly on the raised nubs and tightens in place using the retaining bolt and hex key, Fig.9.
Note: Always make sure the blade is securely fitted before starting the machine. Incorrectly fitted blades can become loose
during operation and can become damaged or cause injury.
OPERATION
TURNING THE MACHINE ON AND OFF (FIG.10)
To start the tool, grasp the handle and slide the switch toward the "I (ON)" position.
Allow the tool to come to full speed before beginning work. Control pressure and surface contact between accessory and
workpiece.
To stop the tool, slide the switch toward the
· 0 (OFF} position. Make sure the tool comes to a complete stop before laying the tool down.
ORBITAL STROKE SPEED (FIG.11)
The orbital stroke rate is adjustable. To change the orbital stroke rate, turn the dial between 1 and 6 (MAX). The higher the
number is, the higher the orbital stroke rate is.
Press the dial to the number suitable for your workpiece.
NOTE: The dial cannot be turned directly from 1 to 6 (MAX) or from 6 (MAX) to 1. Forcing the dial may damage the tool.
When changing the dial direction, always turn the dial moving it through each intermediate number.
LED WORK LIGHT
Caution: Do not look in the light or see the source of light directly.
Slide the switch toward the "1 (ON)" position to light up the lamp. The lamp keeps on lighting while the tool is in the ON position.
The lamp goes out immediately when the switch is in the OFF position.
OPERATION TIPS
SAWING/CUTTING
The sawing teeth are very sharp. Do not touch during mounting and application.
Before sawing make sure that no live cables will be damaged.
The accessory must be inserted firmly or clamped tightly before it is put into operation.
Typical application: wood, plasterboard and soft plastics. Not suitable for metal (e.g. nails) and stone.
Always set the saw blade straight (at 90") and guide it in the gap without tilting.
Always guide the saw blade along the cutting line without exerting any pressure.
When plunging and sawing with a slight pendulum motion, make sure that enough chip removal is provided for.
Keep a certain distance away from hard metals (stone/metal) (approx. 3 mm), since there is increased danger of the outer saw
teeth breaking off.
Use moderate pressure to avoid burning or scorching the workpiece.
SCRAPING
Typical application: Scraping off old varnish or adhesives. Removing glued carpeting, e.g. on stairs or other small to medium-
sized surfaces.
Use light pressure and a low angle to avoid gouging and damaging the workpiece.
SANDING
Typical application: wood, metal, small areas, especially corners, edges and places difficult to access.
Sand with constant movement and light pressure.
Pressing on heavily does not increase the removal - the sandpaper merely becomes worn faster.
The sandpaper lasts longer if the wear is distributed evenly. To ensure even distribution, loosen the sandpaper, tum it around a
little and then tighten again firmly.
MAINTENANCE
WARNING!
Always remove the battery pack from your tool when you are assembling parts, making adjustments, cleaning,
or when not in use. Removing the battery pack will prevent accidental starting that could cause serious personal injury.
This power tool normally requires no maintenance: from time to time the ventilation slots on the motor casing should be cleaned
out. If the unit should become defective, the repair should be performed by an authorized service agent for electric tools.
The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with
compressed air.
Ventilation openings and switch levers must be kept clean and free of foreign materials. Do not attempt to clean by inserting
pointed objects through openings.
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial
solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING! Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with
plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
Electric tools used on fiberglass material, wallboard, spackling compounds or plaster are subject to accelerated wear and
possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc.
Consequently, we do not recommend using this tool for extended work on these types of materials. However. if you do work with
any of these materials, it is extremely important to clean the tool using compressed air.
LUBRICATION
All the bearings in this tool are lubricated with a sufficient amount of high-grade lubricant for the life of the unit under normal
operating conditions. Therefore, no further lubrication is required.
TECHNICAL SPECIFICATION
Voltage
Oscillating angle
Oscillating
Pad size
Sound Pressure Level
Sound Power Level
Vibration Level
18V DC
3.2°
8000-18000 O/min
93x93x93mm
77 dB(A) K=3dB(A)
LwA88 dB(A) K=3dB(A)
4.68 m/s' , K=1.5m/s'