Resumen de contenidos para Sauder Harbor View 420477
Página 1
Harbor View Collection | Model 420477 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.
Página 2
LEFT END (1) BACK (1) M38 SHELF MOLDING (1) TOP (1) SHORT END MOLDING (2) M59 VALANCE (1) SHELF (1) FEET (2) M61 SKIRT (1) BOTTOM (1) M12 TOP MOLDING (1) M71 LONG END MOLDING (2) Page 2 420477 www.sauder.com/services...
Now you know Part Identifi cation our ABCs. www.sauder.com/services 420477 Page 3...
Página 4
METAL PIN - 12 RUBBER SLEEVE - 12 BLACK 9/16" LARGE HEAD SCREW - 37 BLACK 1-7/8" FLAT HEAD SCREW - 2 BLACK 1-1/8" PAN HEAD SCREW - 3 BLACK 1-7/8" PAN HEAD SCREW - 3 Page 4 420477 www.sauder.com/services...
Página 5
Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. To begin assembly, push a SAUDER TWIST-LOCK® å FASTENER (10F) into the large holes in the ENDS (A and B).
Página 6
NOTE: Be sure to use the exact holes shown. å Push three HIDDEN CAMS (1F) into the SHELF (D). å Arrow Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 420477 www.sauder.com/services...
Página 7
HEAD SCREWS (1S). Righty tighty. Lefty loosey. NOTE: Be sure the edges of the ANGLE BRACKETS are å even with the edges of the ENDS. BLACK 9/16" LARGE HEAD SCREW (14 used for the ANGLE BRACKETS) (14 used) www.sauder.com/services 420477 Page 7...
Página 8
Step 4 Fasten the RIGHT END (A) to the TOP (C2). Tighten two å ® How to use the SAUDER TWIST-LOCK FASTENER TWIST-LOCK® FASTENERS. 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. Fasten the SHELF (D) and BOTTOM (E) to the RIGHT å...
Página 9
Step 5 Fasten the LEFT END (B) to the TOP (C2), SHELF (D), and å BOTTOM (E). Tighten six TWIST-LOCK® FASTENERS. Edge with ANGLE BRACKETS www.sauder.com/services 420477 Page 9...
Página 10
NOTE: Do not overtighten the SCREWS into the TOP. å Fasten the SHELF MOLDING (M38) to the SHELF (D). å Tighten three TWIST-LOCK® FASTENERS. Curved edge BLACK 1-7/8" PAN HEAD SCREW (3 used in this step) These surfaces should be even. Page 10 420477 www.sauder.com/services...
Página 11
Step 7 Fasten four TIE PLATES (3G) to the VALANCE (M59). Use four å BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (4 used in this step) www.sauder.com/services 420477 Page 11...
Página 12
NOTE: There are no holes in the LONG END MOLDINGS (M71). Turn the å screws into the grooves of the LONG END MOLDINGS. Do not overtighten. BLACK 9/16" LARGE HEAD SCREW (12 used in this step) These edges must be even. Page 12 420477 www.sauder.com/services...
Página 13
Turn the screws into the grooves of the SHORT END MOLDINGS. Do not overtighten. BLACK 9/16" LARGE HEAD SCREW (6 used in this step) The SHORT END MOLDINGS should be against the SHELF MOLDING (M38). These edges must be even. www.sauder.com/services 420477 Page 13...
Página 14
Step Step 10 Fasten the SKIRT (M61) to the BOTTOM MOLDING (M13). å Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Flat surface Rounded edge Page 14 420477 www.sauder.com/services...
Página 15
Next, turn a FOOT (J) onto each FOOT SCREW (23F). Turn å the FEET clockwise until the FEET and FOOT SCREWS are tight against the BOTTOM MOLDING (M13). BLACK 1-1/8" PAN HEAD SCREW (3 used in this step) www.sauder.com/services 420477 Page 15...
Página 16
NOTE: Perforations have been provided for access å (41 used in this step) through the BACK. Carefully cut out the holes needed. These holes must line up over the SHELF (D). Cut outs used for lifting Page 16 420477 www.sauder.com/services...
NOTE: Before moving your unit to a diff erent location, unscrew the SAFETY DRYWALL ANCHOR (61M) from your wall. å The nylon sheath will remain behind your wall. BLACK 9/16" LARGE HEAD SCREW (1 used in this step) www.sauder.com/services 420477 Page 17...
Página 18
This completes assembly. Clean with your favorite furniture polish or a å damp cloth. Wipe dry. And to celebrate, why not share your success story? No load 25 lbs. 25 lbs. 35 lbs. 25 lbs. (12 used) 35 lbs. Page 18 420477 www.sauder.com/services...
QUANTITÉ d’ a chat de cet élément et conserver le livret pour future référence. EXTRÉMITÉ DROITE .........1 EXCENTRIQUE ESCAMOTABLE .....3 Pour contacter Sauder EXTRÉMITÉ GAUCHE........1 10F FIXATION TWIST-LOCK® ........12 en ce qui concerne cet DESSUS ..............1 14F VIS D'EXCENTRIQUE ..........3 élément, faire référence...
Página 20
éviter d'endommager l'élément ou le sol. ÉTAPE 6 Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (10F) dans les gros trous des EXTRÉMITÉS (A et B). Fixer la MOULURE DE DESSUS (M12) au DESSUS (C2). Utiliser Répéter cette étape pour la TABLETTE (D) et le DESSOUS (E).
Página 21
à l'ARRIÈRE. Découper avec précaution les sécurité fi gurant sur les pages arrière du manuel d’instructions. trous nécessaires. Ceci complète l'assemblage. Nettoyer à l’ a ide d’une encaustique pour meubles ou d’un chiff on humide. Essuyer. www.sauder.com/services 420477 Page 21...
EXCÉNTRICO ESCONDIDO .......3 et conserver le livret pour future référence. EXTREMO IZQUIERDO ..........1 10F SUJETADOR TWIST-LOCK® ......12 Pour contacter Sauder PANEL SUPERIOR .............1 14F BIELA DE EXCÉNTRICO ........3 en ce qui concerne cet ESTANTE ................1 23F TORNILLO DE PIE ............2 élément, faire référence...
Página 23
Para comenzar el ensamblaje, empuje un SUJETADOR PASO 6 TWIST-LOCK® SAUDER (10F) dentro de los agujeros grandes de los EXTREMOS (A y B). Fije la MOLDURA DE PANEL SUPERIOR (M12) al PANEL Repita este paso para el ESTANTE (D) y el DORSO (E).
Página 24
ESTANTE (D). Esto completa el ensamblaje. Limpie con su pulimento para NOTA: Hay perforaciones provistas para el acceso a través del muebles preferido o un paño húmedo. Seque con un paño. DORSO. Cuidadosamente corte los agujeros necesarios. Page 24 420477 www.sauder.com/services...
Página 25
Les téléviseurs peuvent être un téléviseur. cet eff et. particulièrement lourds. De plus, le poids et l’emplacement du tube image ont tendance à rendre les téléviseurs instables et enclins à tomber vers l’ a vant. www.sauder.com/services 420477 Page 25...
Página 26
Además, el peso y la ubicación del tubo de imagen tienden a causar la inestabilidad de televisores y propensa a volcarse hacia adelante. Page 26 420477 www.sauder.com/services...
GARANTIE LIMITÉE DE 5 ANS 1. Sauder Woodworking Co. (Sauder®) off re une couverture de garantie limitée à l’ a cheteur 4. La présente garantie ne s’ a pplique qu’ a ux défauts garantis qui se produisent pour initial du présent produit pendant une période de cinq ans à...
Página 28
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.