Adjustment Options; Additional Functions - swissflex uni 11 95RF Modo De Empleo

Key lock
To avoid improper use of the motor frame, you can lock
the buttons on the remote control. With the exception of
the buttons of the user socket (15), the floor lighting (16)
and the night light (17), which are accessible at all times.
In order to lock the keys, you hold down the memory but-
ton (14) for about 8 to 10 seconds.
A beep will be heard from the receiver. The key lock is
then activated. From now, if other buttons are pressed,
the receiver will emit 3 beeps (indicating that the remote
control is locked), but the slat-base will not move.
Deactivating the key lock
Hold down the memory button (14) for about 8 to 10 se-
conds. The beep emitted by the receiver indicates that the
buttons are reactivated.
Teach-in procedure without the simultaneous function:
1. Press both buttons (1) and (14), (SET Memory and
"all motors combined up") simultaneously and hold
it down. Then press the teach-in button (23) on the
motor control. The motor control confirms the suc-
cessfully teach-in procedure with a sound and the
background lighting on the sender blinks for a short
while. 2. The device is functional 1 sec. after the teach-
in procedure.
Teach-in procedure with the simultaneous function:
The motor control which is to operate a radio remote
control on which the ("SYN ON/OFF") simultaneous
function has not been taught needs to be assigned as
"Master". The other motor control need to be assigned
as "Slave". The next steps are to be as follow: 1. First
teach-in the master. Press both buttons (1) and (14) si-
multaneously and hold it down. Then press the teach-in
button (23) on the motor control of bed 1. The motor con-
trol confirms the successfully teach-in procedure with a
sound and the background lighting on the sender blinks
for a short while. 2. After a pause of about 1 sec., teach-
in the slave. Hold both buttons (14) and (2) pressed and
press the teach-in button (23) on the slave motor con-
trol of bed 2. The motor control confirms the successfully
teach-in procedure with a sound and the background
lighting on the sender blinks for a short while. 3. Repeat
the process with the second radio remote control, but
ex-changing the bed number. (Assign the master to bed
2 and the slave to bed 1). 4. After a short pause (about 1
sec.) check the teach-in procedure with both radio re-
mote control. Also check the simultaneous function.
Night light (LED light)
The night light (accessory floor lighting) can be activated
by pressing one time the button (17).
After 30 minutes it will be automatically switched off,
or by pressing again on the button (17).
14
Operating instructions
Adjustment options
g The various sections can be adjusted using the
function buttons (3 – 10) on the radio remote control.
The sleep and sit positions (position 11 – 13) have
been pre-programmed in the factory. However, you
can adjust and redefine each of these positions.
To programme your preferred positions
g Individually adjust the position with the function but-
tons (3 – 10)
g Press the memory button (14) 3 times
g Press the memory button you want to use once:
Memory position 1 – 3.
Once the electronics have recognised the newly saved
position, a sequence of sounds will confirm your choice.
The programming of a new position automatically
overwrites an old position. If an unchanged position is
programmed under the same memory button, a low
humming tone will sound.
To call up a position stored in memory
g Press the relevant memory button Memory position
1 – 3 until all sections have reached the required final
position.
Selecting the standard pre-programmed positions
g Press the memory button 1, 2 or 3 on the radio
remote control until the sleep surface reaches the
programmed end position. The final position has been
reached when the motors can no longer be heard. The
standard pre-programmed positions can be changed
and individually adjusted (see "Programming your pre-
ferred position").
Resetting all adjustments (horizontal position)
g Press "all motors combined" button "down" (2) until all
comfort areas have reached the horizontal position and
the motors have stopped. In the case of a power failure,
the basic position can only be reached by using the emer-
gency lowering function.
Additional functions
Connecting a second slat base
g Use the synchronisation cable to connect the second
remote control to the first one. The synchronisation cable
for the additional remote control is available from your
Swissflex stockist.
Optional user socket
g The optional user socket is available as an acces-
sory from your Swissflex stockist. The optional user
socket can be used to connect an electronic device
(radio, lamp) that can be switched on and off using the
radio remote control.
GB