Important Safeguards - Andis DBLC Instrucciones De Uso Y Cuidado

E N G L I S H
Please read the following instructions before using your new Andis clipper. Give it the
care that a fine, precision built instrument deserves and it will give you years of service.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should
always be followed, including the following: Read all instructions
before using the Andis Clipper.
DANGER:
To reduce the risk of electric shock:
1. Do not reach for an appliance that has fallen into water. Unplug
immediately.
2. Do not use while bathing or in a shower.
3. Do not place or store appliance where it can fall or be pulled
into a tub or sink. Do not place in or drop into water or other
liquid.
4. Except when charging, always unplug this appliance after use.
5. Unplug this appliance before cleaning, removing or assembling
parts.
WARNING:
o reduce the risk of burns, fire electric shock,
T
or injury to persons:
1. An appliance should never be left unattended when plugged in.
2. This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
3. Children shall not play with the appliance.
4. Use this appliance only for its intended use as described in this
manual. Do not use attachments not recommended by Andis.
5. Never operate this appliance if it has a damaged cord or plug, if
it is not working properly, if it has been dropped or damaged, or
dropped into water. Return the appliance to an Andis Authorized
Service Station for examination and repair.
6. Keep the cord away from heated surfaces.
7. Never drop or insert any object into any opening.
8. Do not use outdoors or operate where aerosol (spray) products are
being used or where oxygen is being administered.
9. Do not use this appliance with a damaged or broken blade or
comb, as injury to the skin may occur.
10. To disconnect turn control to OFF then remove plug from
outlet.
2
11. Plug charger directly into an AC outlet. Do not use an
extension cord.
12. Use of a charger not sold by Andis may result in risk of fire,
electric shock, or injury to person.
13. Do not disassemble charger. Incorrect reassembly may result in
a risk of electric shock or fire. When repair is required, send or
take it to an Andis Authorized Service Station.
14. The battery in this clipper is designed to provide maximum
trouble-free life. However, like all batteries, it will eventually
wear out. Do not attempt to replace battery. When repair or
replacement is required, send or take it to an Andis Authorized
Service Station.
15. Batteries can be harmful to the environment if disposed of
improperly. Many communities offer recycling or battery
collection. Contact your local government about disposal
practices in your area.
16. WARNING: Never touch both terminals on clipper with metal
objects and/or body parts, as short circuit may result. Keep
away from children. Failure to comply with these warnings
could result in fire or serious injury.
17. Keep the appliance dry.
18. WARNING: During use, do not place or leave appliance where
it may be 1) damaged by an animal or 2) exposed to the weather.
SAVE THESE INSTRUCTIONS
OPERATING INSTRUCTIONS
• The battery is to only be replaced by an Andis Authorized Service Station.
• The battery must be removed from the appliance before it is recycled.
• The battery is to be recycled as a lithium-ion battery.
UNIVERSAL AC/DC POWER ADAPTER
1. Remove the wall adapter and charger from the carton.
2. Note the charger comes standard with a universal AC voltage wall adapter and four
interchangeable plugs (Figures A-D).
3. To attach the desired plug to the wall adapter, align the slots on the plug to the ribs on the wall
adapter and slide into place. The plug will "click" into place when properly attached. To remove,
locate the button marked "push" on the wall adapter. Press the button and slide the plug from
the wall adapter. The plugs for the various countries all attach and remove using the same
method (Figure E).
4. Connect the power cord to the back of the charger and then insert the transformer into an
AC outlet.
CHARGING UNIT
To charge, plug wall adapter into 100-240V, 50/60 cycle AC electrical outlet or as noted on the
unit. Make sure the proper input plug is attached to the wall adapter. Plug power cord directly into
back of charging stand. Place clipper into the pocket on the charging stand. The clipper has
electrical contacts that touch electrical contacts in the charger. The weight of the unit will provide
sufficient contact.
3