Descargar Imprimir esta página
Shure SM10A Guia Del Usuario
Ocultar thumbs Ver también para SM10A:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

Enlaces rápidos

MODEL SM10A
DYNAMIC HEAD-WORN MICROPHONE
The Shure SM10A is a low-impedance, unidirectional
dynamic microphone designed for close-talk head-worn
applications such as remote-site sports broadcasting and
corporate intercom systems. It is also ideal for singing
drummers, keyboard artists, and other performers who need
a head-worn vocal microphone with superior noise rejection
and a smooth, natural-sounding frequency response.
The SM10A is very lightweight and is typically mounted on
the supplied steel headband assembly. An adjustable pivot
on the headband assembly allows the microphone boom to
be moved 20_ in any direction. The boom also slides out so
the microphone can be positioned up to 89 mm (3
from the pivot housing. A supplied windscreen reduces wind
noise and explosive breath sounds. A belt clip that fits over
the XLR connector and attaches to the user's belt or
waistband provides cable strain relief.
Features
Designed for close-talk operation; ideal for use in
noisy environments
Unidirectional(cardioid) polar pattern for superior
rejection of unwanted sound
Smooth, natural-sounding frequency response
Adjustable microphone boom with locking pivot can
be moved 20 _ in any direction and extends to 89 mm
1
(3
/
in.)
2
Light weight headband minimizes user fatigue and
does not interfere with eyeglasses
Rugged stainless steel, aluminum and high-impact
plastic construction
A clip that fits over the XLR connector and attaches to
the user's belt or waistband, providing cable strain
relief.
2001, Shure Incorporated
27B3125 (AA)
MOUNTING THE SM10A ON THE HEADBAND
1. Twist the lower headband arms 90_ so they are perpen-
dicular to the headband. As supplied, the retaining clip
is positioned for left side operation. See Figure 1.
NOTE: For right side usage (see photo), remove the re-
taining clip and attach it to the other (unused) hole in the
headband arm so the screw is at the top.
2. Snap the microphone pivot housing into the retaining
clip with the pivot adjustment knob upward and the mi-
crophone toward the front.
3. Loosen the pivot adjustment knob and position the
boom so that the microphone is near the side of the
user's mouth. Then tighten the pivot adjustment knob.
4. Place the assembled microphone on the user's head
and pull the headband arms downward until they are just
above the ears.
5. Loosen the pivot adjustment knob and position the mi-
crophone as close as possible to the corner of the user's
mouth. Then tighten the adjustment knob.
NOTE: For proper operation, the microphone should be
less than 25 mm (1 in.) from the corner of the mouth––
away from the center of the mouth. This will eliminate ex-
plosive breath sounds ("pop").
6. Snap the belt clip over the groove in the XLR connector
at the end of the microphone wire. Then attach the clip
to the user's belt or waistband.
7. Plug the microphone XLR connector into a microphone
1
/
in.)
2
cable or preamplifier.
Headband
Arm
Microphone
SM10A POSITIONED FOR LEFT SIDE OPERATION
1 1
Model SM10A Microphone
User Guide
Pivot
Adjustment
Knob
Retaining
Clip
Boom
Pivot Housing
FIGURE 1
Printed in Mexico
Headband

Publicidad

loading

Resumen de contenidos para Shure SM10A

  • Página 1 (“pop”). The SM10A is very lightweight and is typically mounted on 6. Snap the belt clip over the groove in the XLR connector the supplied steel headband assembly. An adjustable pivot at the end of the microphone wire.
  • Página 2 Open Circuit Voltage: –65.0 dBV/Pa* (0.45 mV) lent, with an integral switch. This connector can be attached *1 Pa = 94 dB SPL to the cable connecting the SM10A to the PA system. Refer to the wiring diagram in Figure 6 Hum Sensitivity (typical) 35.5 dB equivalent SPL in a 1 mOe field...
  • Página 3 ARCHITECTS’ SPECIFICATIONS The microphone shall be a Shure Model SM10A or equiva- lent. The microphone shall be a moving-coil (dynamic) type with a frequency response of 50 to 15,000 Hz. The unit shall have a cardioid polar characteristic. The cancellation at the rear shall be 15 to 20 dB.
  • Página 4 Flexible pivot Une attache s’adapte par-dessus le connecteur XLR et se fixe à la ceinture de l’utilisateur ; elle sert aussi à SM10A POSITIONNÉ POUR L’UTILISATION DU CÔTÉ soulager la tension du câble. GAUCHE FIGURE 1 MONTAGE DU SM10A SUR LE SERRE–TÊTE CARACTÉRISTIQUES...
  • Página 5 COURBE DE DIRECTIVITÉ TYPIQUE MARCHE-ARRÊT FIGURE 3 lmpédance Tel que fourni, le SM10A ne comprend pas d’interrupteur Valeur nominale à 150 Ω (223 Ω réelle) marche-arrêt. Toutefois, il est facile d’en construire un en Sensibilité (1000 Hz à 8 mm [ po]) utilisant un connecteur audio professionnel femelle à...
  • Página 6: Technische Daten

    MODELL SM10A DYNAMISCHES AM KOPF GETRAGENES MIKROFON Das Shure SM10A ist ein niederohmiges, dynamisches; am 5. Den Gelenk-Einstellknopf lösen und das Mikrofon so Kopf getragenes Richtmikrofon für das Sprechen unmittel- anordnen, daß es sich so nahe wie möglich am Mund- bar am Mikrofon wie zum Beispiel Sportberichterstattung winkel des Benutzers befindet.
  • Página 7 55103 (1996) Teil 1 und 2 für Wohngebiete (E1) und Leichtindu- striegebiete (E2). AUSSTATTUNG MIT EIN/AUS–SCHALTER TYPISCHE RICHTCHARAKTERISTIK ABBILDUNG 3 Im Lieferzustand verfügt das SM10A nicht über einen Ein/ Impedanz Aus-Schalter. Mit einer 3–poligen Profi-Tonsteckerbuchse Nennwert 150 Ω (Istwert 223 Ω) mit integriertem Schalter Switchcraft T3F oder gleichwertig Empfindlichkeit (1000 Hz bei 8 mm) läßt sich jedoch auf einfache Weise ein Schalter vorsehen.
  • Página 8 MODELO SM10A MICROFONO DINAMICO DE CABEZA El SM10A de Shure es un micrófono dinámico unidireccio- 4. Coloque el micrófono armado en la cabeza del usuario nal de baja impedancia con soporte para la cabeza que sirve y tire de los brazos de la cinta para cabeza hacia abajo para usos tales como la difusión de eventos deportivos...
  • Página 9 (E1) y zonas de industria ligera (E2). MODIFICACION DE INTERRUPTOR DE ENCENDIDO PATRON POLAR TIPICO FIGURA 3 El SM10A se suministra sin un interruptor de encendido. Sin Impedancia embargo, es posible añadir uno fácilmente usando un co- Nominal: 150 Ω (Real: 223 Ω)
  • Página 10 MODELLO SM10A MICROFONO A CUFFIA DINAMICO Il modello Shure SM10A è un microfono dinamico unidire- 5. Allentate la manopola di regolazione dello snodo e posi- zionale, a bassa impedenza, adatto ad applicazioni in cui zionate il microfono quanto più vicino possibile all’ango- occorre tenere il microfono vicino alla bocca e avere le mani lo della bocca, quindi serrate la manopola.
  • Página 11 MODIFICA PER L’USO DI UN INTERRUTTORE DI DIAGRAMMA POLARE TIPICO ALIMENTAZIONE FIGURA 3 Il modello SM10A non è dotato di un interruttore di alimenta- lmpedenza zione; tuttavia è facile costruirne uno mediante un connetto- Valore nominale 150 Ω (valore effettivo 223 Ω) re audio per uso professionale Switchcraft T3F femmina a Sensibilità...
  • Página 12 SHURE Incorporated Web Address: http://www.shure.com 222 Hartrey Avenue, Evanston, IL 60202–3696, U.S.A. Phone: 847-866–2200 Fax: 847-866-2279 In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414 In Asia, Phone: 852-2893-4290 Fax: 852-2893-4055 Elsewhere, Phone: 847-866–2200 Fax: 847-866-2585...