vigo VG02021 Manual Del Usuario página 3

PACKAGE CONTENT
HOLLOW PIN
COPPER PIN
TWO METAL
FAUCET
BRAIDED HOSES
ASSEMBLY
REQUIRED TOOLS
Adjustable wrench
Allen key - supplied (to remove cartridge if needed)
Plumber's putty - optional
Pipe tape
Flat screwdrivers
SAFETY TIPS
If you use soldering for the installation of the faucet, the seats, cartridges and
washers will have to be removed before using flame. Damage caused by
improper soldering will void the warranty. Protect your eyes with safety
glasses when cutting or soldering water supply lines.
IMPORTANT POINTS
Prior to beginning installation, turn off the cold and hot water lines and open
the hot and cold knobs on the old faucet to release pressure. When installing
your new faucet, turn the connector nuts finger-tight, then use one wrench to
anchor the fitting and a second wrench to tighten the nut. Connections that
are too tight will reduce the integrity of the system. and potentially cause
product failure which could lead to water damage. Wrap all threaded
connections with pipe tape available at your local hardware or plumbing
supply store. Always wrap in a clockwise direction.
Not all necessary supplies to install your faucet are included, however, they
are available wherever plumbing supplies are sold.
Prior to installing the faucet please FLUSH THE HOT AND COLD WATER
SUPPLY LINES that are or will be connected to the new faucet to remove
scale, solder or their impurities which could damage the faucet and potentially
void the warranty.
MAINTENANCE
Your new faucet is designed for years of trouble-free performance. Keep it
looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and harsh chemicals as these will scratch, dull, and/or
damage the finish and void the warranty.
INSTALLATION
Installation must be done by a qualified licensed plumber. Prior to installation
please read the instructions thoroughly, confirm that all parts are included and
visually inspect the unit for any defects. If you have any questions please
contact our Technical Support Department before proceeding with installation.
RUBBER RING COUNTERWEIGHT
METAL RING RUBBER RING
ALLEN KEY (REMOVES
HANDLE TO ACCESS
CARTRIDGE
ASSEMBLY
1. Shut off water supply. Remove
the old faucet and flexible hoses.
Clean sink surface with a
non-abrasive cleaner in prepara-
tion for the new faucet.
NUT
2. Thread female end of metal
braided hose to the faucet (2).
!
Ensure that you use pipe tape
and do not over tighten the
supply line nuts as this could
cause product failure leading
cause product failure leading.
3. Position the faucet in the
countertop hole, from beneath
the countertop hole assemble the
plastic holder, rubber ring, and
metal ring in the order depicted
in the diagram. Then thread the
metal nut onto the hollow pin.
Tighten the metal nut until the
faucet is secure.
!
Ensure that parts are assembled
in the order as depicted in the
diagram to prevent damage to
faucet and supply lines.
4. Screw spray hose to the copper
pin (the longest pin). Make sure to
have a tight seal using adjustable
wrench. Attach supplied counter-
weight to the hose.
!
Do not over tighten connect point as
this could cause product failure
leading to water damage.
5. (if not done already) attach sprayer
to female connection of sprayer hose
by hand and tighten until secure.
Make sure the black washer is seated
and installed properly.
6. Attach the female connections of
the flexible hoses to the cold and hot
water supply.
!
Ensure that you use pipe tape and
adjustable wrench, do not over
tighten as this could cause product
failure leading to water damage.
7. After installation is complete, turn on the water
supply and allow both hot and cold water to run
separately for at least two minutes each. While
water is running, check for leaks. It is important
to view the connections at the male and female
flexible hose connections. If leaks are detected,
refer back to the instructions and adjust
accordingly. Tightening nuts slightly may stop
any minor leaks.
1
2
3
NUT
4
6