SUHNER UWM 8 Documentación Técnica página 4

• If noise level exceeds 85 dB(A) at the work station, sound
insulation and hearing protection measures must be taken
by the operator.
• For additional personal protection, it is advisable to connect
tool to a ground fault circuit interrupter,(only in damp areas).
For additional safety instructions refer to enclosed brochu-
re EW 39 210 01.
Before start-up
Voltage Warning
Before connecting tool to a power source, be sure the voltage
supplied is the same as specified on the name plate of the tool.
The power supply should not vary more than 10% above or
below the voltage indicated on the nameplate.
ON-OFF SWITCH
Before connecting power cord to receptacle, make sure that
switch 11 is in the Off -0- Position.
Operation conditions and instructions
This tool is equipped with an electronic control or a soft start
device. Don't put machine under load until it reached its free
load pick speed.
Cut-off wheels
cutting, don't tilt grinder, otherwise it jams.
Grinding wheels
Best grinding results are achieved if grinder is at a 30 degree
angle to the work piece.
• Never use a cut-off wheel for grinding.
• Do not treat any material containing asbestos.
Attention: Operate machine without force, in order not to draw
excessive current, which causes overheading & finally failure.
Caractéristiques techniques
Puissance absorbée
Puissance rendement
Vitesse à vide
Outils ø max.
UWM 6 / UWM 4
Niveau sonore selon CEN/TC 255 N
Niveau de pression acoustique
Niveau de puissance acoustique
Vibration selon EN 60745
Filetage de broche selon modèle
(voir liste de pièces de rechange)
Poids sans câble environ
UWM 6 / UWM 4
4
3940401_A_BA_UWM8_6_4.indd 4
UWM 8
UWM 6
UWM 4
1'800 Watt
1'200 Watt
-1
UWM 8 8'000 min
UWM 6 6'000 min -1
-1
UWM 4 4'000 min
UWM 8 178 mm
230 mm
95 dB(A)
108 dB(A)
6,3 m/s 2
2
K=1,5 m/s
M 14 ou
5/8" - 11
UWM 8 5,4 kg
5,7 kg
Disconnect Tools
When changing accessories, such as wheels and discs.
• Lock spindle 2 with Lock button 8.
Attention: only use lock button, when machine is at a com-
plete stop.
• Remove or mount flange nut 6 +/or 17 using Pin wrench 7.
Clean mounting set before installation.
Attention: Jammed tools should be removed with open end
wrench instead of lock button devise.
• Check concentricity, use only vibration free tools and always
observe M.O.S. (Max. operating speed).
Maintenance
• Store tool in a clean, dry place.
• Disconnect tool when not in use and before servicing.
• The ventilator openings for cool air must be kept free and
clean, use air gun to blow out dirt.
• Replace grease in grinder head every other time, when
carbon brushes are replaced. Use the Suhner authorized
service center nearest you .
• Damaged plugs and cords must be replaced immediate-
ly.
• Repairs must only be done by a qualified/licensed electri-
cian, otherwise it could be hazardous to the operator.
• Warranty claims can only be considered, if tool is retur-
ned complete.
Accessories
All accessories can be found in the
Tool catalog.
Subject to change.
Classe de protection
Tension (voir liste de pièces de rechange)
Eléments de machine
1 Support pour capot de protection
2 Broche
3 Clé à six pans intérieur, pour capot de
protection
4 Capot de protection
5 Flasque de serrage
6 Ecrou de serrage
7 Clé pour écrou de serrage
8 Bouton d'arrêt pour broche
9 Tête d'angle
10 Poignée
11 Interrupteur
12 Bouton d'arrêt
13 Filetage pour poignée
Abrasive Power
FR
II
diverse
24.04.2008 08:40:34