First Use; Using Your Toothbrush - Oral-B iO Serie Manual De Instrucciones

• This toothbrush is a personal care device
and is not intended for use on multiple
patients in a dental practice or institution.
For hygienic reasons we recommend the
use of individual brush handles and brush
heads for each family member.
• Small parts may come off, keep out of
reach of children.
To avoid brush head breakage which may
generate a small parts choking hazard or
damage teeth:
• Prior to each use, ensure the brush head fits
well. Discontinue use of the toothbrush, if
brush head no longer fit properly. Never use
without a brush head.
• If the toothbrush handle is dropped, the
brush head should be replaced before the
next use even if no damage is visible
• Replace brush head every 3 months or
sooner if brush head becomes worn.
• Clean brush head properly after each use
(see «Cleaning recommendations» para-
graph). Proper cleaning ensures the safe
use and functional life of the toothbrush.
Important Information
• This toothbrush, charger and pouch (acces-
sory) contain NdFeB magnets and generate
magnetic fields. If you use a medical device
or have an implanted medical device, con-
sult with the medical device manufacturer
or a physician, if you have questions about
safely using your Oral-B iO toothbrush.
• Your Oral-B toothbrush can be used with
your smartphone (find details under
«Connecting your toothbrush to your
Smartphone»). To avoid electromagnetic
interference and/or compatibility conflicts,
disable Bluetooth® on your toothbrush
handle (5) before using it in restricted sur-
roundings, such as aircrafts or specially
marked areas in hospitals.
• Disable Bluetooth by entering the «Set-
tings» menu on the interactive display (4)
-> Bluetooth -> disable. Follow the same
procedure to enable Bluetooth again.
• Persons with pacemakers should always
keep the toothbrush more than 15 centime-
ters (six inches) from the pacemaker while
turned on. Anytime you suspect inter-
ference is taking place disable Bluetooth.
Specifications
For voltage specifications refer to the bottom
of the charging unit.
P&G RELEASE 02/03/2020 11:14:34 AM Printed 2020-02-03
91215046_OP020_WE.indd 7 91215046_OP020_WE.indd 7

First use

Please wake up your toothbrush by pressing
the on/off button (7) and follow the instruc-
tions on the interactive display (4) to get
started for first time setup.
If not further instructed on the display, you
may toggle with the mode button (8) and
select with the on/off button (7).
You may change the settings via the «Settings»
menu (17) at any time.
Charging and Operating
• To charge the battery place the toothbrush
on the plugged-in charger (6).
• The charge level is indicated on the inter-
active display (4). Once it is fully charged
the display turns off.
A full charge typically takes 3 hours.
• If the battery is running low the motor
reduces its speed and the Smart Pressure
Sensor (3) shortly blinks in red. Once the
battery is empty, the motor stops; it will
need at least a 5-minute charge for one
usage.
Note: In case the battery is empty (display off),
charge for at least 30 minutes.
• You can always store the handle on the
plugged-in charger to maintain it at full
charge; a battery overcharge is prevented
by the device.
Note: Store handle at room temperature for
optimal battery maintenance.
Caution: Do not expose handle to tempera-
tures higher than 50°C / 122°F.

Using your toothbrush

Start Brushing
Place the brush head on the handle. A small gap
should remain between handle and brush head.
Lift the handle off the plugged-in charger
or simply pick it up to wake up the handle
(display turns on). Wet brush head and apply
toothpaste. To avoid splashing, guide the
brush head to your teeth before switching the
handle on by pressing the on/off button.
Note: Display turns off after some time.
You may press the on/off button to activate
display again.
Page 11 of 114
7
03.02.20 16:19 03.02.20 16:19