Eu Declaration Of Conformity; Faac S.p.a. Soc. Unipersonale; Falcon 14 M - Falcon 14 Mc - Falcon 20 M- Falcon 20; Mc - Falcon 15 M - Falcon 15 Mc - Genius FALCON M Serie Manual Del Usuario

1. DESCRIPTION AND TECHNICAL SPECIFICATIONS
2. DIMENSIONS
3. MAXIMUM USE CURVE
4. ELECTRONIC DEVICES (standard system)
5. INSTALLING THE AUTOMATED SYSTEM
5.1. PRELIMINARY CHECKS
5.2. MASONRY FOR FOUNDATION PLATE
5.3. MECHANICAL INSTALLATION
5.4. INSTALLING THE RACK
6. START-UP
6.1. CONNECTION OF CONTROL BOARD
6.2. POSITIONING THE TRAVEL-LIMIT ELEMENTS
7. AUTOMATED SYSTEM TEST
8. MANUAL OPERATION
9. RESTORING NORMAL OPERATION MODE
10. SPECIAL APPLICATIONS
11. MAINTENANCE
12. REPAIRS
13. ACCESSORIES

EU DECLARATION OF CONFORMITY

The Manufacturer
Company name:

FAAC S.p.A. Soc. Unipersonale

Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
hereby declares under his sole responsibility that the following product:
Description: Gear motor for sliding gates
Model:

FALCON 14 M - FALCON 14 MC - FALCON 20 M- FALCON 20

MC - FALCON 15 M - FALCON 15 MC

Complies with the following relevant Union harmonization legislations:
2014/30/EU
2011/65/EU
Furthermore, the following harmonised standards have been applied:
EN61000-6-2:2005
EN61000-6-3:2007 + A1:2011
Bologna, Italy, 04-12-2018

CEO

A. Marcellan
FALCON M
INDEX
DECLARATION OF INCORPORATION FOR PARTLY
COMPLETED MACHINERY
(2006/42/EC ANNEX II P.1, B)
Manufacturer and person authorised to draft the applicable technical documentation
Company name: FAAC S.p.A. Soc. Unipersonale
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
Hereby declares that the partly completed machinery:
Description: Gear motor for sliding gates
Model: FALCON 14 M - FALCON 14 MC - FALCON 20 M- FALCON 20
MC - FALCON 15 M - FALCON 15 MC
the following essential requirements of the Machinery Directive 2006/42/EC
(including all applicable amendments) have been applied and fulfilled:
1.1.2, 1.1.3, 1.1.5, 1.1.6, 1.2.1, 1.2.3, 1.2.5, 1.2.6, 1.3.1,
1.3.2, 1.3.4, 1.3.6, 1.3.9, 1.4.1, 1.4.2.1, 1.5.1, 1.5.2,
1.5.5, 1.5.6, 1.5.7, 1.5.8, 1.5.10, 1.5.11, 1.6.1, 1.6.4,
1.7.1, 1.7.2, 1.7.3, 1.7.4.2, 1.7.4.3
and that the relevant technical documentation has been compiled in compliance
with part B of Annex VII.
Furthermore, the following harmonised standards have been applied:
EN60335-1:2012 + A11:2014
EN60335-2-103:2015
EN 12100:2010
EN 13849-1:2015 CAT 2 PL "C"
EN 13849-2:2012
Undertakes to transmit by mail or by e-mail, in response to a reasoned request by
the national authorities, relevant information on the partly completed machinery.
It is also declared that the partly completed machinery identified above may not be com-
missioned until the final machine - into which it will be incorporated - has been declared
complaint with the provisions of the above mentioned Machine Directive 2006/42/EC.
Bologna, Italy, 04-12-2018
6
page.7
page.7
page.7
page.7
page.8
page.8
page.8
page.8
page.8
page.9
page.9
page.9
page.10
page.10
page.10
page.10
page.10
page.10
page.10
CEO
A. Marcellan
00058I0616 - Rev.1