Cequent Performance Products 75607 Instrucciones De Instalación

Vehicle Frame
Bumper
Bracket
Access slot 08 &
newer trucks
Hitch Shown In Proper Position
(Bumper bracket shown is
typical 2008 & newer trucks) i l 2008 &
Equipment Required:
Fastener Kit: 75607F
Wrenches: 21mm, 22mm, 11/16"
Drill Bits: None
Other equipment: Tape
Bumper bracket
shown is typical
of 2007 & older
trucks
Tape blocks to outside of
bumper bracket or frame
depending on truck year depending on truck year
Hex Bolt, M14 X 2.00 X 60mm
Qty. (4)
1
5/8" Conical Toothed Washers
Qty. (4)
2
Qty. (4) Block, 5/8" X 1-1/2" X 2-1/8"
3
Carriage Bolt, 7/16"-14 X 1-3/4"
Qty. (2)
4
Block, 1/8" X 7/8" X 2" with square hole.
Qty. (2)
5
1. On 2007 & earlier trucks the bumper brackets are on the outside of the truck frame. On 2008 & newer trucks the bumper
brackets are inside the truck frame. Remove the (2) bolts per side attaching bumper brackets to frame.
2. It helps to tape the 5/8" thick blocks supplied in place to the side of the frame or bumper brackets as shown above before
raising hitch in to place.
3. Install (2) new M14 bolts supplied per side as shown above through hitch, blocks and frame and loosely tighten.
4. Fishwire 7/16" carriage bolts and blocks through truck frame in to holes in truck frame that align with slots in hitch. On 2007 &
older trucks you can fishwire from end of truck frame. On 2008 & newer trucks there is an access slot on outside of frame.
5. Note! Insert 1/2" flat washers supplied as needed between hitch and bottom of truck frame as shown above, both sides. This
is done to take up space created by existing weld on bottom of all truck frames & existing flat washer holding bumper bracket
on newer trucks.
6. Torque all (4) M14 bolts with torque wrench to 115 Lb.-Ft. (156 N*M)
7. Torque both 7/16" bolts with torque wrench to 50 Lb.-Ft. (68 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007, 2008, 2010 Cequent Performance Products
Installation Instructions
Chevrolet Colorado Pickup,
GMC Canyon Pickup & Isuzu "I" Series Pickup
Bumper
Wiring Access location: PU3
Access through slot in outside of
k )
frame 2008 & newer trucks
Access through end of
frame 2007 & older trucks
6
2
1
7
8
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
8
4
5
3
1/2" Flat Washer
Qty. (4)
6
7/16" Conical Toothed Washers
Qty. (2)
7
Qty. (2) Hex Nut, 7/16"-14
8
Wire Leader, 7/16"
Qty. (1)
9
Sheet 1 of 3 75607N
Part Numbers:
75607, 87458,
44593, 78280
Max Gross G Max Tongue
Trailer WT (LB) WT (LB)
7500 (3405 Kg.) 750 (340 Kg.)
6000 (2724 Kg.) 600 (272 Kg.)
4
3
6
7
All Fasteners
Typical Both
Note!
Hitch is
purposely built wide.
Frame brackets will
draw in when
tightened.
6-11-10
Form: F205 Rev A 5-6-05
U-Haul
5
1
2
Sides
Rev. C