Tabla de contenido
Publicidad
OBJ_BUCH-1020-003.book Page 40 Wednesday, July 22, 2015 1:32 PM
Safety warnings specific for sanding operations
Do not use excessively oversized sanding disc
paper. Follow manufacturers recommenda-
tions, when selecting sanding paper. Larger
sanding paper extending beyond the sanding
pad presents a laceration hazard and may cause
snagging, tearing of the disc, or kickback.
Safety warnings specific for wire brushing
operations
Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
overstress the wires by applying excessive
load to the brush. The wire bristles can easily
penetrate light clothing and/or skin.
If the use of a guard is recommended for wire
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel
or brush may expand in diameter due to work
load and centrifugal forces.
Additional safety warnings
Wear safety goggles.
Use suitable detectors to determine if utility
lines are hidden in the work area or call the lo-
cal utility company for assistance. Contact with
electric lines can lead to fire and electric shock.
Damaging a gas line can lead to explosion. Pen-
etrating a water line causes property damage or
may cause an electric shock.
Release the On/Off switch and set it to the off
position when the power supply is interrupted,
e. g., in case of a power failure or when the
mains plug is pulled. This prevents uncontrolled
restarting.
Do not touch grinding and cutting discs before
they have cooled down. The discs can become
very hot while working.
Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
Products sold in GB only: Your product is fitted
with a BS 1363/A approved electric plug with in-
ternal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets,
it should be cut off and an appropriate plug fitted
in its place by an authorised customer service
agent. The replacement plug should have the
same fuse rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be in-
serted into a mains socket elsewhere.
Products sold in AUS and NZ only: Use a resid-
ual current device (RCD) with a rated residual
current of 30 mA or less.
40 | English
Product Description and
Specifications
Read all safety warnings and all in-
structions. Failure to follow the warn-
ings and instructions may result in
electric shock, fire and/or serious inju-
ry.
While reading the operating instructions, unfold
the graphics page for the machine and leave it
open.
Intended Use
The machine is intended for cutting, roughing and
brushing of metal and stone materials without the
use of water.
For cutting with bonded abrasives, a special cut-
ting guard (accessory) must be used.
When cutting in stone, provide for sufficient dust
extraction.
With approved sanding tools, the machine can be
used for sanding with sanding discs.
Product Features
The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 Spindle lock button
2 On/Off switch
3 Auxiliary handle
4 Grinder spindle
5 Protection guard for grinding
6 Encoding key
7 Clamping lever for protection guard
8 Screw for adjustment of protection guard
9 Protection guard for cutting*
10 Mounting flange with O-ring
11 Grinding/cutting disc*
12 Clamping nut
13 Quick-clamping nut
14 Hand guard*
15 Spacer discs*
16 Rubber sanding plate*
17 Sanding sheet*
18 Round nut*
19 Cup brush*
20 Cutting guide with dust extraction protection
guard *
21 Diamond cutting disc*
*Accessories shown or described are not part of the
standard delivery scope of the product. A complete
overview of accessories can be found in our acces-
sories program.
*
1 609 92A 1DS • 22.7.15
Publicidad
Tabla de contenido
