Bosch Sensixx DS37 i-Temp Advanced Instrucciones De Uso página 15

Ocultar thumbs Ver también para Sensixx DS37 i-Temp Advanced:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 73
• This appliance is to be connected and used in
accordance with the information stated on its
characteristics plate.
• This appliance must be connected to an
earthed socket. if it is absolutely necessary to
use an extension cable, make sure that it is
suitable for 16a and has a socket with an earth
connection.
• if the safety fuse fitted in the appliance blows,
the appliance will be rendered inoperative. To
restore normal operation the appliance will
have to be taken to an authorised Technical
Service Centre.
• in order to avoid that, under unfavourable
mains conditions, phenomena like transient
voltage drops or lighting fluctuations can
happen, it is recommended that the iron is
connected to a power supply system with a
maximum impedance of 0.14Ω. if necessary,
the user can ask the public power supply
company for the system impedance at the
interface point.
• The appliance must never be placed directly
under the tap to fill the water tank.
• Unplug the appliance from the mains supply
after each use, or if a fault is suspected.
• The electrical plug must not be removed from
the socket by pulling the cable.
• never immerse the iron in water or any other
fluid.
• Do not leave the appliance exposed to weather
conditions (rain, sun, frost, etc.)
Important:
This appliance reaches high temperatures and
produces steam during use, this could cause
scalds or burns if not used properly.
The steam hose, base station, metal plate at
the bottom of the removable iron pad (2) and in
particular the iron can get hot when used. This
is normal.
never aim the steam at people or animals.
Do not allow the power cable to come into
contact with the soleplate when it is hot.
Be aware that the system can keep on
steaming for a short additional time after
releasing the steam trigger. This is a normal
function.
Description
1. Water tank
2. removable iron pad
3. Energy saving "eco" button (green)
4. "Steam ready" / "auto shut-off" pilot light*
5. Setting selector
6. "refill water tank" /
"Clean warning*" pilot light
7. illuminated main power button (0/i) (red)
8. Housing with internal steam generator
9. Mains cable with storage facility
10. Steam hose
11. iron fixation system "Securelock"
12. "Calc'n'Clean advanced" scale collector
13. Steam release button
14. Steam shot button "pulseSteam"*
15. iron pilot light
16. Soleplate
17. Fabric-protection soleplate cover*
* model dependent
1
preparations
1. release the iron from its lock system (11) by
pulling the lever located at the heel of the iron
backwards.
2. remove any label or protective covering from
the soleplate.
3. place the appliance horizontally on a solid,
stable surface. you may remove the iron pad
from the appliance and place the iron on it on
another solid, stable, horizontal surface.
4. Fill the water tank, making sure not to pass the
"max" level mark.
5. Unwind the mains cable (9) fully and plug it into
an earthed socket.
6. Set the main power button (7) to the on position
(illuminated in red).
7. The "Steam ready" indicator lamp (4) will light
up after several minutes, indicating that the
appliance is ready to use.
The steam generator will take more time to
reach "Steam ready" state only upon the initial
heating up, or after performing the de-scaling
operation (Calc'n'Clean).
When water is already present in the steam
generator during regular use, heat up time to
reach the operating temperature will be faster.
8. This appliance has a built-in water level sensor.
The "refill water tank" indicator (6) will light
when the water tank is empty.
15
BOS CH

Publicidad

Tabla de contenido
loading

Tabla de contenido