Application & Operation; Maintenance - RIDGID TP-160 Manual De Instrucciones De Funcionamiento Y Piezas De Repuesto

Model TP-160 – Operating Instructions and Parts Manual
APPLICATION AND OPERATION
Always disconnect
electric supply before
attempting to install, service, relocate, or
perform any maintenance. If the power
source is out of sight, lock and tag in open
(off) position to prevent unexpected power
application. Failure to do so could result in fatal electrical shock!
Electric shock hazard. Use
only Underwriters Laboratories
(UL)-listed extension cord with # 16 gauge or larger wire
that is labeled for outdoor use. Use polarized grounding
type plugs only. Polarized plugs have one blade slightly
wider than the other and can only be inserted one way into the outlet.
Do NOT handle plug connector near water. Failure to follow these
instructions will result in serious injury or death.
This unit is NOT designed for use as a
sump pump or in sump applications.
This unit is NOT designed for use in septic tanks or
underground vaults to pump raw sewage or effl uents.
NEVER use in hazardous or explosive locations.
1. This pump has been designed with 1-1/4 in. NPT discharge
size. Connect pipe or fitting to the discharge threads, or connect
the supplied garden hose elbow fitting to the pump. Thread the
female end of the garden hose to the male discharge on the
pump.
2. To reduce leakage between the pump and the hose, place a
hose washer (not included) on the garden hose before installing
to the pump.
3. For best pump performance, unwind the hose before starting the
pump. This will help remove any kinks or binds in the hose and
allow the unit to pump with less restriction.
4. Set the pump on a hard, flat surface in the water. Do not set the
pump directly on mud or sand surfaces. This will cause the inlet
screen to clog.
Do not handle pump with wet
hands or when standing in water or
on a damp surface when the unit is operating or fails to
operate. ALWAYS disconnect pump power cord from
power source before handling.
5. Plug the power cord into a grounded 120-volt GFCI power
outlet. The pump will start operating as soon as the power cord
is plugged into the power outlet.
6. The pump will remove water down to 3/8 in. above the hard
surface the pump was placed on.
7. The pump should be turned off once the water level reaches the
3/8 in. mark.
Do NOT allow pump to run dry. The shaft
seal depends on water for lubrication. Operating
pump without water WILL damage the shaft seal and cause pump
failure.
2

MAINTENANCE

service, relocate, or perform any maintenance. Failure to
do so COULD result in fatal electrical shock.
Minimal service is required for this pump. The motor
housing of the pump is completely sealed and requires no service. If
pump should fail to operate, perform the following troubleshooting
guidelines:
1. Verify pumping height does NOT exceed 20 feet
(See Figure 1). If pumping height is greater than 20 feet, this
pump will NOT operate.
Figure 1 - Water Level
these instructions will result in serious injury or death.
2. To verify pump is operating correctly:
a. Disconnect pump from power source.
b. Connect hose adapter and discharge hose to pump.
c. Immerse pump in a bucket or tub of water.
d. Place the other end of the discharge hose outside the
bucket, so the water will pump out.
e. Plug power cord into a grounded 120 volt GFCI power outlet.
If pump operates correctly, proceed to step #3. If pump does
NOT operate, unplug power cord and proceed to step #4 in
this section.
3. To verify discharge hose is free from a blockage:
a. Connect hose to another water source such as a faucet.
If water flows through hose, proceed to step 4. If water is
restricted, verify discharge hose is unwound. Remove all
kinks, bends, or obstructions in hose.
4. Periodic cleaning is required to maintain performance of the
pump. Follow the cleaning steps listed below:
a. Unplug the power cord.
b. Remove the 4 screws in the bottom of the base.
c. Remove the base and inlet plate.
d. Remove the debris and make sure the impeller turns freely.
e. Reinstall inlet plate, base, and screws.
Ridge Tool Company
ALWAYS disconnect electric
supply before attempting to install,
20 FT MAXIMUM
WATER LEVEL
Do NOT disassemble or alter this
product in any way. Failure to follow