BEACON
HIGH DOME
MAGNET MOUNT - ENRBCSHM(x)1(x)Z(xxx)
COMBO: FLAT/PIPE MOUNT - ENRBCSHC(x)1(x)Z(xxx)
LOW DOME
MAGNET MOUNT - ENRBCSLM(x)1(x)Z(xx)
COMBO: FLAT/PIPE MOUNT - ENRBCSLC(x)1(x)Z(xxx)
WARNING
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat
build-up and fire. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle
Owner's Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or fire.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
configuration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal
or local chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at
power source.
•Install protective grommets when routing wire through firewall or metal.
www.soundoffsignal.com/sales-support. If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. or after hours 5 p.m. to 8 p.m. EST
at 1.800338.7337 (press #4 to skip the automated message). Questions or comments that do not require immediate attention may be emailed to techservices@soundoffsigal.com.
1.800.338.7337 / www.soundoffsignal.com
1.
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage. To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at
S U P E R I O R C U S TO M E R R E L AT I O N S H I P S . S M A RT LY D E S I G N E D L I G H T I N G & E L E C T R O N I C S O L U T I O N S .
TECHNICAL SPECIFICATIONS
Dimensions:
Input Voltage:
Operating Temp:
Standby Current:
Reverse Polarity Protection:
Electrical Transient
Protection:
Wiring:
CURRENT CONSUMPTION
MODULE
INPUT VOLTAGE
LED COLOR
CONFIGURATION
RANGE
Amber
Blue
3 LED Single Color
9-32Vdc
Green
6 LED Single Color
White
12 LED Dual Color
18 LED Tri Color
Red
9-32Vdc
Amber
Blue
9-32Vdc
Green
9 LED Dual Color
White
Red
9-32Vdc
Amber
Blue
9-32Vdc
12 LED Single
Green
Color
White
Red
9-32Vdc
Please see pages 2-3 for Mounting Instructions
NOTICE:
Low Dome: 3.6" (9.25cm)H x 8.6" (21.8cm) D
High Dome: 5.3" (13.4 cm) H x 8.6" (21.8 cm) D
Discrete Wiring: 9-32Vdc
Cig Plug, 4-Button Remote: 9-16Vdc
-40°-+65°C
<0.0001 Amps after 10 seconds of no active
control inputs
Yes
ISO7637-2
Approx. 18" length. Type TXL 4x 16AWG
Power/Ground, 6x 20AWG Control
CURRENT
CURRENT
DRAW
DRAW
@12.8Vdc
@25.6Vdc
1.0 Amps
0.5 Amps
0.6 Amps
0.3 Amps
1.4 Amps
0.7 Amps
1.0 Amps
0.5 Amps
1.8 Amps
0.9 Amps
1.4 Amps
0.7 Amps
WARNING
!
This product contains high intensity LED devices. To
prevent eye damage, DO NOT stare into the light
beam at close range.
nROADS Beacon_9-32Vdc 0318
WATTS
(FLASHING)
5.8 Watts
4.2 Watts
8.8 Watts
6.3 Watts
11.7 Watts
8.3 Watts