Soundoff Signal nROADS ENRBCSHM Serie Instrucciones De Montaje página 6

nROADS 4-BUTTON REMOTE
Function:
The 4 button remote can be used to control the nROADS lightbar, when ordered with the corresponding cig plug power harness.
Each button on the remote simulates one of the 4 control wires as found on the discrete wire option.
Pressing a button once will activate the wire function (button backlight turns green.) Pressing the button a second time will de-activate the wire function (button backlight turns red.)
Configuring the Remote:
To configure the remote, activate one or more of the buttons on the front and
then press the program button on the back (using a non conductive tool.) The
mode indicator LED will flash to indicate the programming mode.
1. To change behavior of nROADS for a button/wire:
a. Activate ONE button and then press the program button.
b. Press and hold the same button in the same manner as programming
with wires, where pressing the button now acts as holding the white
programming wire.
c. Press program button to exit to normal operation.
2. To enable or disable buzzer when buttons are pressed:
a. Activate buttons 1 and 2 and then press the program button.
b. Press button 1 to toggle buzzer (green = enabled, red = disabled.)
c. Press program button to exit to normal operation.
3. To set the backlight level:
a. Activate buttons 1 and 3 and then press the program button.
b. Press button 1 to increase brightness or button 2 to decrease
brightness.
c. Press button 4 to toggle whether remote will stay on if nothing active.
i. Button 4 green = remote will stay on as long as power is applied.
ii. Button 4 off = remote will turn off 10 seconds after all outputs are off.
d. Press program button to exit to normal operation.
4. To set green LED level:
a. Activate buttons 1 and 4 and then press the program button.
b. Press button 1 to increase brightness or button 2 to decrease
brightness.
c. Press program button to exit to normal operation.
6.
MODE INDICATOR
4. To set green LED level:
a. Activate buttons 1 and 4 and then press
the program button.
b. Press button 1 to increase brightness or
button 2 to decrease
brightness.
c. Press program button to exit to normal
operation.
5. To display firmware version level:
a. Activate buttons 2 & 3 for remote or 2 &
TOLERANCES
EXCEPT AS NOTED
.X ± .020
4 for nROADS light bar
.XX ± .012
.XXX ± .006
ANGLES ± .5°
version, then press program button.
GD&T TO FOLLOW
ASME Y14.5M-2009
MATERIAL:
b. Firmware version will blink on buttons:
i. Button 1 = major version number
ii. Button 2 = minor version number
iii. Button 3 = build version number
6. To bring nROADS module through learn
mode (only needed if modules are
changed):
a. Activate all 4 buttons and then press the
program button.
Mode Button Flash Indications:
The mode button will flash red if an error
occurs. The error mode is indicated by the
number of blinks.
PROGRAM BUTTON
Mode Button Flash Indications
# OF
ERROR MODE
BLINKS
Bus wire is shorted to ground or
1
power.
2 No nROADS device detected.
Connected nROADS device firmware
3
is too old and not compatible.
Connected device responded with
4
error code.
Programming Modes
SW1 SW2 SW3 SW4 MODE
X PROGRAM WIRE 1
X PROGRAM WIRE 2
X PROGRAM WIRE 3
X PROGRAM WIRE 4
X X ENABLE/DISABLE BUZZER
X X PROGRAM BACKLIGHT LEVEL
X X PROGRAM LED LEVEL
X X DISPLAY REMOTE FW VERSION
X X DISPLAY nROADS FW VERSION
X X X X LEARN MODE
TOLERANCES
EXCEPT AS NOTED
.X ± .020
.XX ± .012
.XXX ± .006
ANGLES ± .5°
GD&T TO FOLLOW
ASME Y14.5M-2009
MATERIAL:
MODE LED
CONTINUOUS FLASH
CONTINUOUS FLASH
CONTINUOUS FLASH
CONTINUOUS FLASH
WINK 1
WINK 2
WINK 3
OFF
OFF
OFF
nROADS Beacon_9-32Vdc 0318