Bayco 908 Instrucciones

Instructions for Models 908 / 975
26 Watt Fluorescent Work Lights
Electrical Rating - All models use 125 Volts 60 Hz
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE - PULL
PLUG
WHEN SERVICING, CONNECTING/DISCONNECTING FROM THE LAMP OR WHEN
RE-LAMPING - USE ONLY 13 WATT OR SMALLER BULB
CAUTION
DO NOT use in explosive atmospheres, near flammable liquids, or where explosion
proof lamps are required.
DO NOT use in the proximity of vehicles or equipment when there is a risk of flammable
liquids coming into contact with the hand lamp.
DO NOT immerse in water.
DO NOT use in areas where water can accumulate or in rain or mist.
CAUTION: Risk of Electric Shock – For Light Duty Dry Location Use Only.
IMPORTANT SAFETY INSTRUCTIONS
This product has a 3 prong polarized plug on the power cord. Do not attempt to
bypass this safety feature by removing the round plug and defeat his safety feature. This
plug will fit into a grounded outlet only one way. If the plug does not fit fully into the outlet,
contact a qualified electrician. Never use with a two wire extension cord.
WARNING: NOT FOR USE IN HAZARDOUS LOCATIONS
CAUTION: DO NOT USE IN HAZARDOUS LOCATIONS AS REQUIRED BY THE
CANADIAN ELECTRICAL CODE, PART I
OPERATION
Plug into 120 Volt 60 Hz polarized outlet. Notice the polarized plug and insert
properly. Operate switch. Lamp may flash several times before lighting.
Some models have a 3-wire grounded outlet as a power source for electrical tools
or other appliances not exceeding 6.4 AMPS. The outlet will also accept a two-wire
polarized plug.
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.baycoproducts.com
BULB REPLACEMENT
1. Disconnect the work light from electrical outlet.
2. Remove the lens cover screws located on each side at the top end of the lamp.
3. Pull the lens out and up to expose the bulbs.
4. Slide the bulb holder from around the bulbs. The bulbs will remain in the socket.
5. Grasping the bulb at the top, rock the bulb back and forth while carefully pulling up
on bulb to remove and discard the old bulb.
6. Insert new bulb in socket and bulb holder. Be sure bulb is properly seated against
the bulb-holder.
7. Slide the lens back into place until it snaps in place.
8. Align the holes in the lens with the holes in the side of the light. Replace the screws.
9. Restore power connection and test lamp by pressing the power switch
NOTE: Even new lamps will flash several times before lighting.
REPLACEMENT BULBS
Use PL-13 twin-tube fluorescent bulb.
A replacement lamp may be obtained from Bayco products.
WARRANTY
1 YEAR WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship
and materials to the original purchaser for 1 year from the date of purchase, and includes
the LEDs, housing, lenses, electronics, switches, rechargeable batteries and chargers.
Bulbs (other than LEDs) are covered for 90 days from the date of purchase.
We will repair or replace this product should we determine it to be defective. This is the
only warranty, expressed or implied, including any warranty of merchantability or fitness for
a particular purpose.
For a complete copy of the warranty, go to www.baycoproducts.com/bayco-product-
support/warranties. Retain your receipt for proof of purchase.
Instructions Pour les
Modèles 908 / 975
26 Watt Lampes de Travail Fluorescente
Caractéristiques électriques - Tous les modèles utilisent 125 volts 60Hz
ATTENTION - POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE ET INCENDIE
- RETIRER LA FICHE
LORS DE L'ENTRETIEN, CONNEXION / DECONNEXION DE LA LAMPE OU
QUAND REMPLACEMENT DES LAMPES - UTILISER SEULEMENT 13 WATTS OU
MOINS AMPOULE
ATTENTION
NE PAS utiliser des atmosphères explosives, près de liquides inflammables, ou
lorsque des lampes antidéflagrantes sont nécessaires.
NE PAS utiliser à proximité de véhicules ou d'équipement quand il ya un risque de
liquides inflammables entrent en contact avec la lampe de poche.
Ne pas plonger dans l'eau.
NE PAS utiliser dans les zones où l'eau peut s'accumuler ou dans la pluie ou le
brouillard.
ATTENTION: Risque de choc électrique - Pour la lumière endroit sec Duty Utilisez
uniquement.
CONSIGNES DE SÉCURITÉ IMPORTANTES
Ce produit a une fiche à 3 broches polarisées sur le cordon d'alimentation. Ne pas
essayer de contourner ce dispositif de sécurité en retirant le bouchon rond et la défaite
de son dispositif de sécurité. Cette fiche dans une prise de terre une seule façon. Si la
fiche n'entre pas complètement dans la prise, contacter un électricien qualifié. Ne pas
utiliser avec un cordon à deux fils d'extension.
ATTENTION: NE PAS UTILISER DANS DES ENDROITS DANGEREUX
ATTENTION: NE PAS UTILISER DANS DES ENDROITS DANGEREUX AS REQUIS
PAR LE CODE ELECTRIQUE CANADIEN, PARTIE I
INS-SL-908-975-18