IMER M400 SMART Manual De Uso & Mantenimiento página 12

Connect the saw plug to the mains and tighten the mechanical retainer
ring with IP67 protection rating.
The saw is now ready for operation. ***
Connect the mains power cable to the plug on the electrical panel Now
start the sawing machine with the switch on the electrical cabinet over
the motor, composed of two buttons: green for start, red for stop.
power failure, press the green button again to resume operation.
In the event of an emergency, press the protruding red pushbutton to
shut down the machine and disconnect the plug from the power mains.
Fill the water tank to the maximum level (approx. 40 litres). Connect the
machine to the power mains and start as described in paragraph 10.
of cooling water to the diamond blade.
Rest the material to be cut on the cutting table against the stopper. Set
the required inclination using the goniometer. To adjust the cutting head
height, loosen the handwheel (Fig.1, Ref. D), position the head at the
required height, then fully tighten the handwheel. There is a stop next
to the handwheel (Fig.1, Ref.D), which must be moved to adjust for the
cutting depth of the disc being used (350mm or 400mm) to prevent the
carriage itself being cut. With the 350mm disc, set the stop as shown in
(Fig.3, Ref.B). With the 400 mm disc, set the stop as shown in (Fig.3,
Ref.C). Start the saw as described in paragraph 10. To make the cut,
place the part to be cut (Fig.3, Ref.D) on the carriage,then push it
towards the disk placing the hands on the sides of the plane, as shown
in Fig.3, Ref.E. If the feed speed is too fast in relation to the thickness
and hardness of the material the blade might stop turning. In this case,
release the disc as quickly as possible by moving the carriage back until
the disc recovers its nominal rotation speed. Resume cutting, adjusting
the feed speed according to the characteristics of the material.
Routine maintenance operations can also be performed by non-
relative sections of this manual are observed at all times.
The machine should be cleaned exclusively when it is stationary.
residue into corners.
2. Ensure that the cooling water nozzles are not obstructed.
3. In particular, it is recommended that you change the cooling water in
the tank every day.
4. Do not use detergents or lubricants.
IMER INTERNATIONAL S.p.A.
M400 SMART
Clean the tank in the event of build-up of sediment on the base, or at
least once a day. Failure to clean the tank could impair operation of
the immersion pump used for circulation of the diamond blade cooling
water.
To clean out the tank, remove its plug and rinse it out with a jet of water
- take care not to direct water onto electrical equipment.
reduced) clean the cooling water supply circuit.To do this, disassemble
the delivery nozzle located inside the blade guard (Fig.1, Ref. E) and
clean in water.
Periodically clean the cooling water delivery line between the pump and
valve and blade guard using water.
The diamond blade is made of material that may be damaged when
subject to high temperatures, and therefore must be cooled during the
work phases.
To replace the blade, proceed as follows:
1. Block the vertical movement of the cutting head by tightening down
the handwheel (Fig.1, Ref.D).
2. Disassemble the front guard (Fig.1, Ref.E).
3. Loosen the locknut by rotating it clockwise (LH thread), using the 32
mm wrench supplied with the machine.
4. Move the cutting head forward slightly and incline to remove the blade
from its seat.
diamond blade. During disassembly, avoid use of tools that could dent
6. Fit the new blade by proceeding in reverse order of the operation
described at point 4. Take special care to ensure the correct direction of
rotation of the diamond blade.
7. Tighten the blade locknut fully down by rotating anticlockwise (left
thread), to a torque of 40 Nm.
Repairs to the electrical installation must be performed exclusively
by specialised personnel. Use exclusively original IMER spare parts;
the M400 SMART ensures that no other maintenance other than that
immediately
As regards disposal of processing waste, observe all current legislation
in the country of use.
Although the sawing machine has been manufactured fully in compliance
with current regulations, residual risks exist that cannot be eliminated
and involve the use of appropriate individual protection devices. The
machine is equipped with notices to indicate the residual risks and how
to avoid them.
12
GB
. If oxidation is detected, clean