Technical Data; Angle Grinder; Angle Grinder Safety Warnings; English - AEG WS 10-115 Manual Original

TECHNICAL DATA

Angle Grinder

Rated input
Rated speed
D= Grinding disk diameter max.
d= Grinding disk hole diameter
b= Cutting disk thickness min. / max.
b= Grinding disk thickness max.
D= Grinding surface diameter max.
D= Wiring brush diameter max.
Thread of work spindle
Weight according EPTA-Procedure 01/2003
Noise information
Measured values determined according to EN 60745. Typically, the A-weighted noise levels of the tool are:
GB
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 60745
Surface grinding:
Vibration emission value a
Uncertainty K=
Disk sanding:
Vibration emission value a
Uncertainty K=
For other applications, e.g. Abrasive Cutting-Off Operations or Wire Brushing other vibration values could occur.
WARNING!
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications,
with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
WARNING!
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.

ANGLE GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding, Wire
Brushing or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder,
sander, wire brush or cut-off tool. Read all safety warnings,
instructions, illustrations and specifications provided with

English

14
h,SG
h,DS
WS 10-115 WS 10-125 WS 12-115 WS 12-125 WS 13-125 XE
1000 W 1000 W 1200 W
11500 min 11500 min 11500 min
-1 -1
115 mm 125 mm 115 mm
22,2 mm 22,2 mm 22,2 mm
1/3 mm 1/3 mm 1/3 mm
6 mm 6 mm 6 mm
115 mm 125 mm 115 mm
75 mm 75 mm 75 mm
M 14 M 14 M 14
2,3 kg 2,3 kg 2,4 kg
87,1 dB (A) 87,1 dB (A) 87,1 dB (A) 87,1 dB (A) 90,1 dB (A)
98,1 dB (A) 98,1 dB (A) 98,1 dB (A) 98,1 dB (A) 101,1 dB (A)
6,2 m/s 6,2 m/s 6,2 m/s
2 2
1,5 m/s 1,5 m/s 1,5 m/s
2 2
6,0 m/s 6,0 m/s 6,0 m/s
2 2
1,5 m/s 1,5 m/s 1,5 m/s
2 2
this power tool. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
b) Operations such as polishing are not recommended
to be performed with this power tool.Operations for which
the power tool was not designed may create a hazard and cause
personal injury.
c) Do not use accessories which are not specifically
designed and recommended by the tool manufacturer. Just
because the accessory can be attached to your power tool, it does
not assure safe operation.
d) The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool. Accesso-
ries running faster than their rated speed can break and fly apart.
1200 W 1300 W
11500 min 2800 - 11500 min
-1 -1
125 mm 125 mm
22,2 mm 22,2 mm
1/3 mm 1/3 mm
6 mm 6 mm
125 mm 125 mm
75 mm 75 mm
M 14 M 14
2,4 kg 2,4 kg
6,2 m/s 8,0 m/s
2 2 2
1,5 m/s 1,5 m/s
2 2 2
6,0 m/s 7,5 m/s
2 2 2
1,5 m/s 1,5 m/s
2 2 2
-1