Technical Data - AEG WSL 180 Instrucciones De Uso

TECHNICAL DATA

Nominal power output (W) ..............................................................
Rated output (W) ............................................................................
Max. no-load speed (min ) .............................................................
-1
Grinding disk diameter (mm) ..........................................................
Thread of work spindle ..................................................................
Weight without cable (kg) ...............................................................
Typical weighted acceleration in the hand-arm area (m/s
Typical A-weighted sound levels:
Sound pressure level (dB (A)) .....................................................
Sound power level (dB (A)) .........................................................
Wear ear protectors!
Measured values determined according to EN 50 144.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the attached
leaflet!
Appliances used at many different locations including open air
must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes and
apron.
Sawdust and splinters must not be removed while the machine is
running.
Always disconnect the plug from the socket before carrying out
any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
After switching off, the machine will not be idle immediately.
(After-running of the work spindle.) Allow the machine to come to
a stop before putting down.
Never reach into the danger area of the plane when it is running.
Always use the auxiliary handle.
Always use the protecting cap when roughing-down and
separating.
Only use tools whose permitted speed is at least as high as the
highest no-load speed of the machine.
Pay attention to the dimensions of the grinding disc. The
mounting hole diameter must fit the mounting flange without
play. Do not use reducer pieces or adapters.
Check grinding tools before use. The grinding tool must be
properly mounted and turn freely. Perform a test run for at least
30 seconds without load. Do not use damaged, out of round or
vibrating grinding tools.
Immediately switch off the machine in case of considerable
vibrations or if other malfunctions occur. Check the machine in
order to find out the cause.
Always use and store the grinding disks according to the
manufacturer's instructions.
When grinding metal, flying sparks are produced. Take care that
no persons are endangered. Because of the danger of fire, no
combustible materials should be located in the vicinity (spark
flight zone). Do not use dust extraction.
Due care should be taken that no sparks or sanding dust flying
from the workpiece come into contact with you.
Never use a cutting disc for grinding. Do not subject cutting discs
to side pressure.
When separating stone the guide shoe must be used!
The adjusting nut must be tightened before starting to work with
the machine.
The workpiece must be fixed if it is not heavy enough to be
steady. Never lead the workpiece to the grinding disk with your
hand.
In case of extreme operating conditions (e.g. when smoothing
metals with the supporting disk and vulcanised fibre disks) strong
contamination can build up inside the angle grinder. In this case,
it is necessary to clean the inside thoroughly and free it from any
metal deposit, due to safety reasons. A residual current
operated device must be superposed. After the current operated
device has come into action, the machine must be subjected to
maintenance.
Inrush currents cause short-time voltage drops. Under
unfavourable power supply conditions, other equipment may be
affected. If the system impedance of the power supply is lower
than 0,2 Ohm, disturbances are unlikely to occur.
19 ENGLISH
WSL 180 WS 180 S
..... 2000 ........... 2300 ............2000 .............2000 ..........2300 ..... 2100
..... 1200 ........... 1400 ............1200 .............1200 ..........1400 ..... 1250
..... 8500 ........... 8500 ............6600 .............6600 ................. 6600
...... 180 ............. 180 ..............230 ...............230 ................... 230
..... M 14 ........... M 14 ............M 14 .............M 14 ................. M 14
...... 5,2 ...............5,5 .............. 5,4 ................ 5,4 ..................... 5,7
) ............ ...... 4,6 ...............4,3 .............. 4,0 ................ 4,0 ..................... 4,0
2
....... 92 ............... 95 ................92 .................92 ..................... 95
...... 105 ............. 108 ..............105 ...............105 ................... 108
SPECIFIED CONDITIONS OF USE
This angle grinder can be used for separating and grinding many
different materials, e.g. metal or stone. In case of doubt please
read the manufacturers' instruction.
Do not use this product in any other way as stated for normal
use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 50144, EN 55014-1, EN 55014-2, EN 61000-3-2,
EN 61000-3-3 (WSLB 230, WSLB 230 X, WSB 230 S), EN
61000-3-11 (WS...), in accordance with the regulations 98/37/
EC, 89/336/EEC
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the system
voltage indicated on the rating plate. It is also possible to
connect to sockets without an earthing contact as the design
conforms to safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Use only AEG accessories and spare parts. Should components
need to be exchanged which have not been described, please
contact one of our AEG service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the ten-digit No. as well as the machine type printed on the
label and order the drawing at your local service agents or
directly at: AEG Elektrowerkzeuge, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
STARTING CURRENT LIMITED (WSLB 230, WSLB 230 X, WSB 230 S)
The starting current for the machine is several times greater than
rated current. The starting current limited produces the starting
current to such an extent that a fuse (16 A, slow-blow) is not
tripped.
SYMBOLS
WSL 230 WSLB 230 X
WSLB 230
Volker Siegle
Manager Product Development
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the machine.
Always disconnect the plug from the socket
before carrying out any work on the machine.
Accessory - Not included in standard
equipment, available as an accessory.
WSA 230 S
WSB 230 S
230 V 110 V