System Start-Up; Schematic Of Figure 1: Ks5 & Ks10 Controller; Diagrama De La Figura 1: Control De Los Sistemas Ks5 Y Ks10 - Krystal Pure KS5 Manual Del Propietário

tank.
C. Take out the ½" 90° elbow hose barb and
remove the rubber washer and plastic nut.
D. From the outside of the brine tank, install the
elbow fitting through the bottom hole.
E. Place the rubber washer onto the threads
inside the brine well and secure with the
plastic nut.
F. Remove the nylon nut from the float
assembly; insert the float assembly inside the
brine well with the bolt through the small hole
opposite the elbow fitting. Secure with the
nylon nut.
STEP 4 SYSTEM START-UP
KS5 AND KS10 START UP:
NOTE: The following steps will require turning the indicator knob (see Figure 1 below) to various po-
sitions. Push the indicator knob in while manually rotating the camshaft located behind the controller
by hand (COuNterCLOCKwiSe) until indicator knob points to the desired position.
1. Remove valve cover by releasing the plastic
clip from the back and lifting the cover up and
forward.
2. Rotate indicator knob to the BACKWASH
position (COUNTERCLOCKWISE).
3. Fill the softener/conditioner tank with water.
a. With house water supply off, open the
SourceSelect™ bypass valve.
b. Open water supply valve very slowly to
approximately ¼ open position.
4. When all of the air has been purged from
the tank (water begins to flow steadily from
the drain), open the main water supply all the
way. Allow water to run to drain until clear.
5. Turn off water supply and let the unit stand
for about five minutes to allow all trapped air
to escape from the tank.
6. Add the initial amount of water to the brine
tank manually with a bucket or a hose. Add
approximately 3 gallons of water to the brine
tank.
7. Slowly turn the water supply valve
completely open. Place the conditioner
into operation by turning the indicator knob
COUNTERCLOCKWISE to the BRINE/
SLOW RINSE position.
8. With conditioner in this position, observe the
water level in the brine tank for several min-
utes to check that the level is going down. If
water level does not recede, then make sure
the brine line fittings are tight and no air can
leak into connections.
KS15HE START UP:
NOTE: The following steps will require turning the cycle indicator (see Figure 2 on pg. 12) to various
positions. Manually rotate the camshaft, located behind the controller, by hand (COUNTERCLOCK-
11 • 02/17 KPWS
G. Connect one end of the 3/8" black line to the
brine float fitting located at the top of the brine
well inside the brine tank. NOTE: The brine
line enters the brine tank through the hole
aligned with the fitting for the brine float.
H. Connect the other end of the 3/8" black line
to the brine line flow control fitting located just
behind the control head using the black nut
provided. The line enters from the left side
facing the control.
I. Be sure all fittings and connections are tight.
(See diagram on page 21).
KS5 • KS10 CONTROLLER
CONTROL DE LOS SISTEMAS KS5 • KS10
Water Flow Indicator
Indicador del flujo de agua
PM Indicator
Indicador de PM
Time
Indicator Knob
Locking Pin
Perilla guia
Clavija asegura-
dora del tiempo
Time Set Button
Botón "Time Set"
FIGURE 1 • FIGURA 1
9. Advance the indicator knob to the FAST
RINSE/REFILL position. Let conditioner run
in this position for a minute or so.
10. Advance the indicator knob to just past the
FAST RINSE/REFILL position but NOT all
the way to the CONDITIONED WATER posi-
tion. Run water from a nearby faucet until the
water is clear. Proceed to Step 5 Electrical
Connections.
Hour Time Display
Ventana de presentación
Raised
Tab
Aleta
alzada
Jumper
Transformer Plug
Interruptor
Receptacle
Spare
Receptor del
Jumper
transformador
Interruptor
extra