Ec Declaration Of Conformity; Technical Data - EUCHNER ZXE Manual De Instrucciones

Operating Instructions Enabling Switch ZXE
Version
ZXE-091336
Version
ZXE-104833
ZXE-120348
Version
Tab terminals for the working contacts
ZXE-111276
C2
Fig. 3: Dimension drawing, ZXE enabling switch
EUCHNER GmbH + Co. KG Kohlhammerstraße 16 D-70771 Leinfelden-Echterdingen Tel. +49 711 7597-0 Fax +49 711 753316 info@euchner.de www.euchner.de
27,5
M22 x 1
Screw terminals for the working contacts
43,5
14
24,8
< 27,5>
ZXE-104833
M22 x 1 20
NO1 C1 NO2
Screw terminals for the working contacts
25,5 1,2
33,5
C1 NO1 NO2
25
< 27,5>
M22 x 1
20
NO 1 C1 NO 2 C2
20,5
Front panel cut-out
ZXE-120348
20
C2 NC2 C2 NO1 C1
20,5
Front panel cut-out
20

EC declaration of conformity

The manufacturer named below herewith declares
that the product fulfills the provisions of the
directive(s) listed below and that the related standards
have been applied.
EUCHNER GmbH + Co. KG
Kohlhammerstraße 16
70771 Leinfelden-Echterdingen, Germany
Directives and standards applied:
Three-position enabling switch
f
- Machinery directive 2006/42/EC
- EMC directive 2004/108/EC
- EN 60947-5-8:2006
Leinfelden, March 2013
Dipl.-Ing. Stefan Euchner
Director
Duc Binh Nguyen
Authorized representative empowered to draw up
documentation
The signed EC declaration of conformity is included
with the product.

Technical data

Parameter Value
Housing material Polyamide, color black
Protective cap material CR, color black
Weight Approx. 30 g
Degree of protection a front IP65
ccording to IEC 60529 connections IP00
Mechanical life min.
Position 1-2-1 1x10 cycles
5
Position 1-2-3-1 1x10 cycles
5
Ambient temperature -5 ... +60 °C
Degree of contamination
3 (industrial)
(external, acc. to EN 60947-1)
Installation position Any
Impact strength > 100 N
Switching elements
ZXE-091336/ZXE-104833/
ZXE-111276 2 NO contacts
ZXE-120348 1 NO contact + 1 NC contact
Connection Screw terminal 4-pin/
tab connector, 4-pin
Tightening torque, max.,
0.15 Nm
of the screws
Conductor diameter single-conductor 0.3 - 1.4 mm,
AWG 22 - 16
Conductor nominal Single-conductor 1.5 mm²,
cross-section flexible wire 1 mm², AWG 16
Insulation stripping length 5 mm
Rated impulse
U = 1.5 kV
imp
withstand voltage
Rated insulation voltage U = 30 V
i
Rated short-circuit current 100 A
Utilization category
DC-13 0.1 A 24 V
acc. to EN 60947-5-2
Breaking capacity max. 250 mW
Switching current max. 100 mA
Switching current min. 5 mA
External fuse
100 mA medium slow-blow
U (+LA) / U (+LB)
Reliability figures acc. to EN ISO 13849-1
B 1 x 10
5
10d