Ap Windows Client Login - Tripp-Lite NetDirector B064-008-01-IPG Manual De Instrucciones

3. Logging Into the B064-Series KVM Switch
You have two options:
• If you are working on a computer other than your own, accept
the certificate for just this session by clicking Yes.
• If you are working at your own computer, install the certificate.
After the certificate is installed, it will be recognized as trusted.
To install the certificate, do the following:
a) In the Security Alert dialog box, click View Certificate. The
Certificate Information dialog box appears.
Note: You may need to run Internet Explorer as an Administrator in
order to view and install the certificate.
b) Click Install Certificate.
c) Follow the Installation Wizard to complete the installation.
Unless you have a specific reason to choose otherwise,
accept the default options.
d) When the Wizard presents a caution screen, click Yes.
e) Click Finish to complete the installation and click OK to
close the dialog box. The certificate is now trusted.

3.3 AP Windows Client Login

In some cases, the Administrator may not want the B064-Series
KVM Switches to be available via browser. The Windows AP Client
allows Windows systems users access to the KVM switch without
having to go through a browser.
The AP Windows Client can be found in the Download Section of the
OSD or on the CD that came with your B064-Series KVM Switch.
If you do not have access to the CD, and browser access to the
KVM switch has already been disabled, you will need to obtain the
file from your system administrator. Once you have saved the AP
Windows Client, go to its location and double-click the WinClient.exe
icon to bring up the Windows Client Connection Screen.
Note:
1. If you have trouble opening the AP Windows Client, save it to your
desktop and try again.
2. When accessing the AP Windows Client for the first time, you will be
prompted to provide a serial number. This serial number can be found
on the CD included with your KVM.
3.3.1 The Connection Screen
A description of the contents of the Connection Screen is given in the following table:
Item Description
Menu Bar The Menu Bar contains two menus; File and Help. The File Menu allows the operator to Create, Save, and Open Work files.
Each time the WinClient.exe file is run, it searches the User's LAN segment for B064-Series KVM Switches, and lists the ones it finds in this
box. Double-click on any of the units in this list to connect to it.
Server List Note: For a switch to show up in the Server List, the Enable Device List check box in the Operating Mode page (see Operating Mode section
under Device Management in OSD Operation for details) must be checked and the Program service port in the Network page (see Network
section under Device Management in OSD Operation for details) must be set to the same number as in the AP Windows Client Port field.
This area is used when you want to connect to a B064-Series KVM Switch at a remote location.
• Click on the IP drop-down and select an address from the list. If the address you want is not listed, key in the target IP
address in the IP field, and its port number in the Port field.
Server
• When the IP address and port number have been specified, click Connect to bring up a login dialog box. Provide a
Username and Password as provided by your system administrator and click OK to establish a connection with the B064-
Series KVM Switch.
• When you have finished with your session, click Disconnect to end the connection.
Message List Lists status messages regarding the connection to the B064-Series KVM Switch.
Switch to Once a remote connection with a B064-Series KVM Switch has been established, this button becomes active. Click it to switch to the KVM
Remote View Switch's Main OSD Page.
Upon installing the certificate or accepting the unrecognized
certificate for the current session, the browser login dialog box
appears.
3. Provide a valid Username and Password (set by the KVM switch's
administrator), and click Login to bring up the OSD Main Page.
Note:
1. If you supply an invalid login, the authentication routine will return and
Invalid Username or Password message. If you see this message, log in
again, being careful to enter the correct Username and Password.
2. If logging in for the first time, a "Change Password" prompt will appear
after the login prompt requiring you to change the default password.
7