General Information - Varian Turbo Cart Manual De Instrucciones

GENERAL INFORMATION

This equipment is destined for use by professionals. The
user should read this instruction manual and any other
additional information supplied by Varian before operat-
ing the equipment. Varian will not be held responsible for
any events occurring due to non-compliance, even par-
tial, with these instructions, improper use by untrained
persons, non-authorised interference with the equipment
or any action contrary to that provided for by specific na-
tional standards. The following paragraphs contain all
the information necessary to guarantee the safety of the
operator when using the equipment. Detailed information
about the installed equipment are available into the sup-
plied relevant technical manuals.
This manual uses the following standard protocol:

WARNING!
The warning messages are for attracting the attention of
the operator to a particular procedure or practice which,
if not followed correctly, could lead to serious injury.
!
The caution messages are displayed before procedures
which, if not followed, could cause damage to the
equipment.
NOTE
The notes contain important information taken from the
text.
DESCRIPTION
The Turbo Cart is a pumping group and is composed of
the following units:
− a Turbo pump with relevant accessories;
− a backing pump;
− the Turbo pump controller;
− a Multigauge or senTorr unit (optional).
The Turbo Cart is factory assembled with the required
pumps and accessories. The base models are the following:
− Model 969-8400: Cart with Turbo-V250 pump with
CFF 6" input flange;
− Model 969-8401: Cart with Turbo-V250 pump with
ISO 100 input flange;
− Model 969-8402: Cart with Turbo-V300HT pump with
CFF 6" input flange;
− Model 969-8403: Cart with Turbo-V300HT pump with
ISO 100 input flange;
− Model 969-8404: Cart with Turbo-V550 pump with
CFF 8" input flange;
− Model 969-8405: Cart with Turbo-V550 pump with
ISO 160 input flange;
− Model 969-8406: Cart with Turbo-V700HT pump with
CFF 10" input flange;
− Model 969-8407: Cart with Turbo-V700HT pump with
ISO 200 input flange;
CAUTION
− Model 969-8408: Cart with Turbo-V70 pump with
CFF 4.5" input flange;
− Model 969-8409: Cart with Turbo-V70 pump with ISO
63 input flange;
− Model 969-8410: Cart with Turbo-V70D pump with
CFF 4.5" input flange;
− Model 969-8411: Cart with Turbo-V70D pump with
ISO 63 input flange;
− Model 969-8412: Cart with Turbo-V70LP pump with
CFF 4.5" input flange;
− Model 969-8413: Cart with Turbo-V70LP pump with
ISO 63 input flange;
− Model 969-8414: Cart with Turbo-V150HT pump with
CFF 6" input flange;
− Model 969-8415: Cart with Turbo-V150HT pump with
ISO 100 input flange.
The following figure shows a Turbo Cart overall view
with indication of the units position.
The following table, with reference to the above men-
tioned figure, lists the Cart base models items.
MOD. POS.
969-8400 1
2
3
969-8401 1
2
3
969-8402 1
2
3
969-8403 1
2
3
82
INSTRUCTIONS FOR USE
Elevation
Width: 395 [15,5]
Dimensions: mm [inches]
Turbo Cart
ITEM
Turbo-V250 pump , CFF 6" flange
Mechanical pump SD40
Controller Turbo-V250
Turbo-V250 pump, ISO 100 flange
Mechanical pump SD40
Controller Turbo-V250
Turbo-V300HT pump, CFF 6" flange
Diaphragm pump MD60
Controller Turbo-V300HT
Turbo-V300HT pump, ISO 100 flange
Diaphragm pump MD60
Controller Turbo-V300HT
87-900-887-01(C)