EN
Instruction for Use
Thank you for buying Philips LivingColors!
LivingColors has been especially designed to create your own ambiance
at home, through color and light.
If using LivingColors for the first time, please read these instructions
carefully and save them for future reference. By following our guidelines,
you will enjoy the full functionality of Philips LivingColors.
Important:
-Carefully remove the parts from the packaging.
-Check whether all parts are available.
Getting started:
1. Open the battery compartment of the remote control by sliding
the button at the back. Insert 2 AAA batteries (+ and – as
indicated) (drawing a).
2. Place LivingColors at a selected location on a flat and stable surface.
Direct LivingColors towards the wall (the optimal distance is
20 inch), Plug your LivingColors into the power system (drawing b).
3. Switch on LivingColors by briefly pressing the "I" (on) on the on/off
button placed on the remote control.
4. Create your own ambiance by:
-Rotating the color wheel. You can move your finger over the color
wheel to refine the color (drawing c).
-Changing the color saturation (adding more white to the current
color). Press on ( ) for a deep color or on ( ) for a more pastel
color (drawing d). Ultimately you will reach the white color.
-Dimming. Increase (
) or decrease ( ) the light intensity via the
dimming buttons (drawing e).
5. Switch off LivingColors by pressing the "0" (off) button briefly.
LivingColors will remember your last color setting for your next
usage.
Do more with LivingColors:
1. Automatic color-changing mode
Sweep your finger around the color wheel (one full circle) and
briefly press on "I" ("On"); LivingColors will then turn into the
automatic color-changing mode: the lamp will start changing colors
automatically.
You can adjust the speed with which colors change. Speed can be
adjusted clockwise, from fast (dark blue color on the color wheel)
to slow (purple) (drawing f). You can rotate anywhere on the color
wheel. While in the automatic color changing mode, you can also
adjust the saturation and brightness of the colors.
To switch back to static color mode, sweep around the color wheel
again, then press "0". Alternatively, you can switch LivingColors off
"0" and on "I" again.
2. Favorite Buttons:
With your LivingColors you can store your two favorite colors for
easy recall.
To store your favorite color, first select it using the color wheel
(and dimming/color intensity) on the remote control. Then press
and hold one of the Favorite Buttons until the LED indicator
(hidden underneath the intensity up symbol) blinks (this will take
+/- 5 seconds). Your favorite color is now stored under the Favorite
440401838521.indd 2
Button (
or
) that you have pressed. Whenever you want
to go back to your favorite color, just press one of the Favorite
Buttons. The LivingColors will now show your favorite color.
You can also store a particular Automatic Color Change Mode
in this way.
3. Linking LivingColors lamps
1. You can operate multiple LivingColors with one remote
control. The LivingColors lamps will then project the same color
(or will change colors simultaneously). In order to link several
LivingColors to one remote control, bring the remote close to
the Philips logo on the top of the lamp and press on "I" ("On").
LivingColors will flash 3 times, and then quickly flash green. You
can release the button now. The linked lamps will turn to the last
setting of the remote control.
- Repeat this operation for each LivingColors lamp that you want
to link with the others.
- To use the LivingColors separately again, link it to another
remote control in the same way as described above.
2. It is also possible to control one LivingColors lamp with several
remote controls. In order to do so, first reset one of the remotes.
Then hold two remote controls close to each other and press
the "I" button on both for 10 seconds. You can now link the new
remote control to the LivingColors in the same way as described
above.
- LivingColors that are linked to two (or more) remote controls
can be controlled by either remote control.
- To unlink a remote control from a LivingColors, hold the remote
control close to the LivingColors and press "0" for three
seconds. The LivingColors will flash 3 times. Hold the "0" button
a little longer and it will slowly fade to off. The remote control
and the LivingColors are now unlinked.
4.Compatibility with timers
You can use LivingColors with a timer (not included). When
switched on with a timer, the LivingColors will show your last
setting (static color or automatic color-changing mode)
Cleaning and maintenance:
Remove the plug from the wall socket.
To avoid scratching, the LivingColors lamp, remote control and
adapter should only be cleaned with a soft dry cloth.
Do not use cleaning agents.
Safety instructions:
Keep the plug and LivingColors away from liquids and humidity.
- LivingColors is for indoor use only. Do not use in wet locations,
e.g. bathrooms or outdoors.
- LivingColors is not a toy designed to be played with by children.
- Do not place on hot surfaces
- For safety reasons and under the terms of the warranty, the
LivingColors and plug must not be opened.
- Only use the adapter supplied: using a different adapter can
damage your LivingColors.
Environment:
If you need to discard the appliance, dispose of it in accordance with
instructions from the local authority. Remove the batteries when
you discard the remote control. Do not throw the batteries away
with normal household waste. They must be handed in at an official
collection point, both of which will dispose of the batteries in an
environmentally friendly way.
2
11/6/2012 11:06:09 AM