Electrical Connection - Scheppach bg150 Traducción De La Instrucción De Original

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 18
• Use outdoor extension leads. When the tool is used
outdoors, use only extension leads intended for outdoor
use and so marked.
• Stay alert. Watch what you are doing. Use common sense
and do not operate the tool when you are tired.
• Check damaged parts. Before further use of the tool, it
should be carefully checked to determine it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by
an authorized service center unless otherwise indicated
in this instruction manual. Do not use the tool if the
switch does not turn it on and off.
• Warning: The use of any accessory or attachment other
than one recommended in this instruction manual may
present a risk of personal injury.
• Have your tool repaired by a qualified person. This
electric tool complies with the relevant safety rules.
Repairs should only be carried out by a qualified person
using original spare parts, otherwhise this may result in
considerable danger to the user.
Additional Safety Rules for Bench Grinders
• Wear protective glasses.
• Do not use damaged or unshaped wheels.
• The adjustment of the spark guard shall be made
frequently, so as to compensate the wear of the wheel,
keeping the distance between the guard and the wheel
as small as possible, and no greater than 2 mm.
• The adjustment of the work rest shall be made frequently,
so as to compensate the wear of the wheel, keeping the
distance between the work rest and the wheel as small
as possible, and no greater than 2 mm.
• Use wheels that have a bore exactly equal to the arbor
of the grinder. Do not attempt to machine an undersized
wheel to fit an arbor.
• Do not overtighten wheel nut.
• Do not grind on a cold wheel. The grinding wheel should
be started and run at idle speed for one minute before
applying the work.
• Do not grind on the side of the wheel. Grind on the face
of the wheel only.
• Do not apply coolant directly to a grinding wheel. Coolant
can weaken the bonding strentgh of the wheel and cause
it to fail.
• Sparks are a hazard. Do not grind near gas or flammable
liquids.
• Stand to one side of the wheel when turning on the
power. Dress the wheel on the face only. Dressing the
side of the wheel can cause it to become too thin for safe
use.
• Grinding creates heat. Do not touch the work piece until
you are sure it has cooled down sufficiently.
• Use grinding wheels that are rated for safe use on the
grinder. Do not use a wheel that is rated lower than the
grinder speed.
Installation
Know your bench grinder (Fig. 1)
1. Eye shield
2. Spark guard
3. Grinding wheels (left: 60 grit, right: 36 grit)
4. Work rest
5. Work light
6. Wheel Guard
7.Bolt Hole for Bench Mounting
8.Main Switch (On/Off)
9. Cooling water container
Assembly
Warning! Never connect the plug to power source outlet
until all installations and adjustments are completed and
you have read and understood sthe safety and operation
instructions.
Assembly bg 150
Work Rests (Fig. 1, Nr. 4)
Install the work rest with a star grip screw , a washer and
a hex nut M6 to the wheel guard. The distance between
wheel and work rest should not exceed 2 mm.
Spark Guards (Fig. 2)
Install the spark guard with a cross-head screw
a washer to the wheel guard. The distance to the wheel
guard should not exceed 2 mm.
Wheel Guards (Fig. 3+4)
Install the eye shield with 2 cross-head screw n M4, 2
washers and 2 hex nuts to the clamping plate.
Lead the handle into the clamping plate and fix it with a
flat head screw M6, a washer and a nut.
Fix the complete unit to the wheel guard with U-handle,
hex bolt M8 and a washer.
The guard is individually adjustable, as to protect the users
eyes during grinding process.
Assembly bg 200
Work Rests (Fig. 5, Nr. 4)
In order to assemble the work rest losen the lower screw
of the wheel guard. Fix it with this screw in the upper
slit, while mounting below the hex bolt M5 with a washer.
The distance between grinding wheel and work rest shall
not exceed 2 mm.
Spark Guards (Fig. 6)
Install the spark guard with a cross-head screw and a
washer to the wheel guard. The distance to the wheel
guard should not exceed 2 mm.
Wheel Guards (Fig. 7+8)
Install the eye shield with 2 cross-head screw n M4, 2
washers and 2 hex nuts to the clamping plate.
Lead the handle into the clamping plate and fix it with a
flat head screw M6, a washer and a nut.
Fix the complete unit to the wheel guard with U-handle,
hex bolt M8 and a washer.
The guard is individually adjustable, as to protect the users
eyes during grinding process.

Electrical connection

The installed electric motor is factory connected ready for
operation.
The connection meets the applicable VDE and DlN
regulations.
The connection made by the customer as well as any
extension cables used must comply with all relevant
regulations.
Connection and repair work on the elctric equipment must
be carried out by a qualified technician only.
Important note
The motor rating is S 1. This means that when overloaded
it switches off automatically. After a cooling period (can
vary) you may switch it on again.
and
english 7

Publicidad

Tabla de contenido
loading

Tabla de contenido