Tabla de contenido
Publicidad
B) PHONO ENCODING
1)
SET THE FUNCTION BUTTON TO " PHONO " MODE AND THEN PRESS THE " RECORD " BUTTON (9)
DIRECTLY.
2)
THE LCD DISPLAY WITH SHOW THE WORD "
" & "
" AND FLASHING AFTER FEW SECONDS. NOW THE SYSTEM IS STARTING THE ENCODING
MODE.
3)
START PLAYBACK AT PHONO FOR THE TRACK WHICH YOU WANT TO RECORD TO USB.
4)
AFTER FINISH OF RECODING, PRESS AND HOLD THE " RECORD " BUTTON (9) UNTIL THE LCD STOP
FLASHING AND RETURN TO " PHONO " MODE.
C) ENCODING BITRATE (BY REMOTE HANDSET)
YOU CAN SELECT THE DESIRED BITRATE DURING ENCODING FROM CD OR PHONO TO USB, THE
SELECTABLE RANGE FROM 32 / 64 /96 /128 / 192 / 256 KBPS.
1)
SET IN " PHONO " FUNCTION (15) & REMAIN STOP MODE.
2)
PRESS THE " INFO " FUNCTION AND THE LCD DISPLA WILL SHOW THE DEFAULT BITRATE (128 KBPS)
3)
PRESS SKIP
4)
PRESS AGAIN THE " INFO " TO CONFIRM THE SETTING AND THE LCD DISPLAY (18) RESUME TO
" PHONO " MODE
D) TRACK SEPARATION (BY REMOTE HANDSET)
YOU CAN DIVIDE THE RECORDING MUSIC FROM PHONO TO USB/SD TRACK BY TRACE DURING ENCODING.
EVERY TIME WHEN PRESS THE "
DURING ENCODING FROM PHONO TO USB/SD, THE SYSTEM WILL GENERATE A NEW TRACK AND
CONTINUOUS THE RECRODING. THE TEXT " PHONO " AT LCD DISPLAY WILL FLASHING ONE TIME, IT MEAN
THE UNIT IS CREATING A NEW TRACK SUCCESSFULLY.
REMOVING OF USB / MEMORY CARD
TO REMOVE THE USB / MEMORY CARD, TURN OFF THE POWER OR SWITCH THE FUNCTION MODE TO
EITHER CD, AUX OR TUNER FIRST. FOR USB PORT – UN-PLUG IT BY PULLING OUT THE USB SOCKET
DIRECTLY, FOR MEMORY CARD – PRESS THE MEMORY CARD INWARD & THEN RELEASE, NOW THE CARD
BEING PARTIALLY EJECT AND YOU CAN REMOVE IT BY HAND.
PHONO
NOTED:
-
REMOVE THE STYLUS PROTECTOR.
-
BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM
REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.
1.
SELECT TO " PHONO " FUNCTION FROM FUNCTION SELECTOR (15)
2.
SET THE SPEED SELECTOR TO THE PROPER POSITION DEPENDING ON THE RECORD TO BE PLAYED.
3.
PLACE THE RECORD ON THE PLATTER (USE THE SPINDLE ADAPTOR IF REQUIRED).
4.
LIFT THE TONE ARM FROM THE REST AND SLOWLY MOVE IT TO THE RECORD SIDE.
THE PLATTER WILL START TO ROTATE.
5.
PLACE THE TONE ARM TO THE DESIRED POSITION OF THE RECORD.
6.
ADJUST THE VOLUME TO THE DESIRED LEVEL.
7.
AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING. LIFT
THE TONE ARM FROM THE RECORD AND RETURN IT TO THE REST.
8.
TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE REST.
REMARK : AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT SETTING, SO IT WILL
STOP BEFORE THE LAST RACK FINISH. IN THIS CASE, SELECT THE AUTO-STOP SWITCH (29) TO " OFF
" POSITION, THEN IT WILL RUN TO THE END OF THE RECORD BUT WILL NOT STOP AUTOMATICALLY (TURN
OFF THE UNIT BY POWER BUTTON OR SWITCH BACK THE AUTO-STOP SWITCH TO " ON " POSITION TO
STOP THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE REST POSITION.
LINE OUT CONNECTION
YOU CAN CONNECT THE SYSTEM TO YOUR WHOLE HI-FI SYSTEM BY CONNECTING THE LINE OUT SOCKET
(26) TO THE AUXILIARY INPUT SOCKET WITH A RCA CABLE (NOT INCLUDED).
SELECT THE BUILT-IN SPEAKER SWTICH (28) TO " OFF " POSITION IF YOU WANT TO CUT-OFF THE SOUND
FROM BUILD-IN SPEKAER WHEN CONNECTING TO OTHER HI-FI SYSTEM THOUGH LINE OUT JACK.
OR
BUTTONS (3) TO SELECT THE DESIRED BITRATE FOR ENCODING.
" (TRACK SEPARATION) BUTTON ONCE AT REMOTE HANDSET
USB
" AND THEN FLASHING, AND THEN DISPLAY "
GB-5
Publicidad
Tabla de contenido
