Tabla de contenido
Publicidad
GB
Storage of the battery
In order to prolong the life of the battery, it is required to provide adequate storage conditions. The batteries can go through
approximately 500 „loading - discharging" cycles. The battery must be stored between 0 and 30°C, at the relative humidity of
50%. In order to store the battery for a prolonged period, it is required to charge it to approximately 70% of its capacity. In case of
prolonged storage, it is required to recharge the battery once a year. Do not permit excessive discharging of the battery, since this
would reduce its life and may cause irreversible damage. During storage, the battery will be gradually unloading due to leakage
conductance. The process of automatic unloading depends on the temperature of storage, since the higher the temperature, the
fastest the process. In case of incorrect storage of batteries, there is a danger of electrolyte leakage. In case of leakage, it is
required protect the leakage with neutralizing agent. In case of contact of electrolyte with the eyes, it is required to rinse the eyes
abundantly, and then immediately seek medical assistance. It is prohibited to use a tool with a damaged battery. In case the
battery is completely worn out, it is required to deposit it at a special point dedicated to disposal of such waste.
Transport of the batteries
Lithium-ion batteries are in accordance with legal regulations treated as dangerous waste. The user of the tool may transport the
tool with the battery or only batteries by land. Then no additional conditions must be complied with. In transport is realised by third
parties (for example dispatch through courier service), then it is required to proceed in accordance with regulations for transport
of dangerous materials. Before shipment, contact an authorised person.
It is prohibited to transport damaged batteries. During transport the battery must be removed from the tool, and the exposed
contacts protected, e.g. with insulating tape. Protect the batteries so that they do not move inside the package during transport. It
is also required comply with the national regulations for transport of dangerous materials.
Charging the Battery
Caution! Before charging, disconnect the charger from the power supply by removing the plug from the power supply socket. In
addition, clean the battery and battery clamps of dirt and dust with a soft, dry cloth.
The battery has a built-in charge indicator. The LEDs will light up by pressing the power button (V), the more of them come on, the
more charged the battery is. If the LEDs do not light up when the button is pressed, the battery is discharged.
Disconnect the battery from the tool. The battery is secured in the tool socket by means of a latch. The battery can be removed by
pressing and holding the latch and then pulling the battery out of the socket. A battery which is correctly installed in the tool socket
cannot be removed other than by pressing the latch.
Slide the battery into the charger socket (V).
Plug the charger into a mains socket.
The red LED will light up, which indicates the charging process.
When charging is complete, the red LED will turn off and the green LED will light up to indicate that the battery is fully charged.
Pull the charger plug out of the mains socket.
Pull the battery out of the charger socket by pressing the battery clamp button.
Caution! If the green LED lights up when the charger is connected to the mains, the battery is fully charged. In this case, the
charger will not start the charging process.
Operating instructions
Do not use the product otherwise than as a mixer for mortars, paints and other liquid building materials. Do not mount any acces-
sories other than agitators, e.g. sanding discs, polishing discs, drills, etc. on the mixer. Do not use the mixer to mix loose products.
All accessories fi tted to the mixer must have a maximum speed greater than the rated product speed. It is forbidden to use acces-
sories with a maximum permissible speed lower than the rated speed of the product.
Damaged agitators must not be used. If cracks are noticed or the agitator shaft is bent, replace it with a defect-free agitator. Check
the condition of the accessories and product before each start-up.
Use agitators designed to work with a given type of material to be mixed. The agitator spindle rotates clockwise and the agitator
must be selected so that it aerates or deaerates the mixed mass. In the case of aeration, the agitator basket is designed in such
a way that during mixing a vortex will form on the surface of the mass to suck in the air. In the case of deaeration, the agitator is
designed so that no vortex is generated and the air in the mass is pushed out of it.
The size of the agitator mounting thread must be the same as the mounting thread of the agitator. Do not use reducing compo-
nents to mount the agitator in the tool. It is forbidden to modify the mixer mount or the accessory mount in order to make it com-
patible with each other. To ensure that the mixer is correctly fi tted, start the mixer without load for 30 seconds in a safe position.
When excessive vibration or other signs of malfunction or damage occur, stop the device immediately and check the mounting
for correctness.
Ensure that the ventilation openings are clear. If necessary, disconnect the product from the power supply by unplugging the plug
or disconnecting the battery pack and clean the tool from dust. Do not use metal objects for this purpose. Clean with a soft paint
brush, a soft brush or a compressed air stream with a pressure of not more than 0.3 MPa.
Always wear safety glasses and hearing protectors. Other personal protective equipment such as dust masks, gloves, helmets,
and aprons should be worn. Long hair should be pinned up.
After the tool is switched off , the agitator still rotates for some time.
O R I G I N A L
I N S T R U C T I O N S
14
Publicidad
Tabla de contenido
