Maintenance / Service; Declaration Of Conformity - Skil F0151061 Serie Manual Del Usuario

• Changing saw blades 8
! insert blade to full depth with teeth facing forward
9
! use T-shank blades only
• Sawing at 15°/30°/45° 0
• Adjusting sawing speed to material used !
! if the tool does not run with wheel D in position 1,
select a higher sawing speed and lower the
sawing speed while the tool runs
• Dust suction @
- connect vacuum cleaner to extension E
! do not use vacuum cleaner when cutting metal
• Selecting sawing mode #
Use lever F 2 for adjusting the orbital action from
accurate cutting (= 0) to fast cutting (= III)
- 1 setting ("0") for accurate cutting in all materials,
straight + curved
- 3 settings for fast cutting in different materials, straight
cuts only
I = metal
II = plastic
III = hard wood
! always select "0" when sawing splinter-sensitive
material
• Laser line $
- for guiding tool along desired line of cut marked on the
workpiece
- switch on/off laser line by pressing switch G
- before starting a job, check the alignment of the laser
line with the actual line of cut by making a trial cut on a
piece of waste material
! do not attempt to adjust the laser line with screw
X which is pre-set at manufacturing
! do not remove or damage warning label A 2
• Operating the tool
- before switching on the tool, ensure that front end of
footplate rests flat on the workpiece
- hold tool firmly with both hands, so you will have full
control of the tool at all times
! while working, always hold the tool at the
grey-coloured grip area(s) %
- ensure that complete surface of footplate rests firmly
on the workpiece
! ensure that the blade has come to a complete
standstill, before you lift the tool from the
workpiece
- keep ventilation slots H 2 uncovered
APPLICATION ADVICE
• Use the appropriate saw blades ^
! use T-shank blades only
• When cutting metals, lubricate saw blade regularly with
oil
• Use parallel guide J for making parallel cuts &
• For an accurate straight cut, guide tool with footplate
along the edge of a straight piece of wood *
• Pre-drill a hole before making cut-outs (
• Splinter-free cutting
- cover cutting-line with several layers of wide tape
before cutting
- always face the good side of the workpiece down
• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots H 2)
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol ) will remind you of this when the need for
disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that the product
described under "Technical data" is in conformity with the
following standards or standardization documents: EN
60745, EN 61000, EN 55014, in accordance with the
provisions of the directives 2004/108/EC, 2006/42/EC,
2011/65/EU
• Technical file at: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
09.12.2013
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 88 dB(A) and the sound
power level 99 dB(A) (standard deviation: 3 dB), and the
vibration ✱ (hand-arm method; uncertainty K = 1.5 m/s²)
✱ when cutting wood 6.7 m/s²
✱ when cutting metal 11.4 m/s²
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
11