Operating Instructions (Original) - MIRKA DEROS 325 Serie Instrucciones De Manejo

en (original)
Operating instructions
• The tool is intended to be operated as a hand held tool. The tool can be used in any position. Note! The sander can
develop a torque reaction when started.
• Make sure the sander is switched off. Select a suitable abrasive and secure it to the backing pad. Make sure the abrasive
is centred on the backing pad. For optimal performance we recommend a Mirka backing pad and Mirka Net Sanding
product.
• Switch on the sander by pressing the On/Off key, Figure 1. The sander LED (right) is now green.
• The sander can now be started by pressing the lever.
• The speed can be adjusted between 4,000 rpm and max rpm by adjusting the position of the lever.
• The max rpm can be adjusted by pressing rpm+ or rpm–, Figure 1. Each press increases or reduces the speed by 1,000
rpm until it reaches the limits. The rpm can be adjusted in the range 4,000 to 10,000 rpm.
• The tool has two speed control modes. In the default mode the speed can be adjusted linearly by changing the position
of the lever. In the other mode the speed remains fixed at the set max rpm when the tool is running. When the rpm+
and rpm– buttons are pressed simultaneously the tool toggles between the two controlling modes.
• When sanding, always place the tool on the work surface before starting the tool. Always remove the tool from the
work surface before stopping it. This will prevent gouging of the work surface due to excess speed of the abrasive.
• When sanding is finished, turn off the sander by pressing the On/Off key. The sander LED (right) is now turned off.
Bluetooth
This tool is equipped with Bluetooth® low energy technology and can be connected to an app from which additional
tool functionality can be accessed. For more information on the app functionality and if it is available in your country, go
to www.mirka.com/mymirka
Activate Bluetooth on your Mirka
Connect the power cord to mains outlet.
1.
Press and hold the Speed+ button while switching the tool on with the On/Off button.
2.
3. Left LED lights up (green), to indicate that Bluetooth is active.
4. Bluetooth is deactivated when the tool is disconnected from mains outlet.
NOTE! If the app is not installed or if it is not available in your country, Bluetooth shall not be activated.
®
The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such
marks by Mirka Ltd is under license. Other trademarks and trade names are those of their respective owners.
FCC Rules & Industry Canada's licence-exempt RSS
Compliance with the radio regulations in North America has been verified in accordance with FCC Part 15 subpart B and
C, RSS-GEN, RSS-247 and FCC §15.247. Operation is subject to the following two conditions:
This device may not cause harmful interference.
1.
This device must accept any interference received, including interference that may cause undesired operation.
2.
NOTE! This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION TO THE USER: Changes or modification not expressly approved by the party responsible for compliance could
void the user s authority to operate the equipment.
14
Mirka® DEROS & 325X, 350X, 550X, 625X, 650X, 680X & 5650X
®
DEROS as follows: