Description And Operation - LEGRAND Wattstopper FSP-311B Instrucciones De Instalación

No: 25746 – 7/19 rev. 8
Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: FSP-311B, FSP-311B-S, FSP-311B-D
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
The FSP-311B is an IP66 rated motion sensor that dims lighting from high to low
based on movement.
Three configurations are available. The FSP-311B mounts inside the fixture and
the PIR lens connects to the FSP-311B through a 1.30" diameter hole in the
bottom of the fixture. The FSP-311B-S mounts to a fixture/enclosure with a 1/2"
knock out, via a nipple on the back. The FSP-311B-D has a drop mount nipple,
for mounting on to a pole, or to a fixture.
The sensor uses passive infrared (PIR) sensing technology that reacts to changes
in infrared energy (moving body heat) within the coverage area. Once the sensor
stops detecting movement and the time delay elapses, lights will go from high to
low mode and eventually to an OFF position if it is desired. Sensors must directly
"see" motion of a person or moving object to detect them, so careful consideration
must be given to sensor luminaire placement and lens selection. Avoid placing the
sensor where obstructions may block the sensor's line of sight.
The FSP-311B operates single phase at 120V/230V/240V/277V. No power pack
is required. It is designed to be installed in indoor and outdoor environments.
NOTE: When the FSP-311B is powered up the first time, it will use factory default parameters to operate. If adjustments are needed,
the Sensor Configuration mobile app must be used.
SPECIFICATIONS
Voltage .................... 120V–277V, 50/60Hz, Single Phase
Load Ratings
@ 120V ...0–800W Tungsten, Ballasts or LED Driver
@ 277V ................... 0–1200W Ballast or LED Driver
@ 230–240V ............. 0–300W Ballast or LED Driver
Motor @ 120V/277V........................................1/6 HP
Wiring .................................................................... 18AWG
Length .......36" (91.44cm), 30" (76.2cm) from nipple
Line Voltage ................................ Line, Neutral, Load
Low Voltage ..................... Dim + (violet), Dim - (gray)
Operating Temperature ......-40°F (-40°C) to 167°F (75°C)
Tightening Skirt/Nut Torque ............................ 25–30 in-lbs
Dimensions
Collar ..................................1.30" diameter (33.0mm)
Collar height ......................................0.64" (16.3mm)
Body .. 5.7"L x 2.3"W x 3.5"H (145mm x 60mm x 90mm)
Weight ........................................................... 2.8 oz (80 g)
Enclosure ............................................. IP66 (NEMA STD)
Coverage
FSP-L2 Lens @ 8' height ..............up to 44' diameter
FSP-L3 Lens @ 20' height ............up to 40' diameter
FSP-L7 Lens @ 40' height ..........up to 100' diameter
Regulatory
Operating Control ............................................Type 1
Pollution Degree .......................................................2
Software .........................................................Class A
Impulse Voltage Rating ....................................... 4kV
Independently mounted for nipple or through hole

DESCRIPTION AND OPERATION

Wattstopper
High/Low/Off, PIR Fixture Integrated Outdoor Sensor In IP66 Enclosure
with Bluetooth
Haut/Bas/Éteint, Luminaire avec capteur IRP extérieur intégré dans un
boitier IP66 avec Bluetooth
Sensor PIR para luminarias de exterior, tipo IP66 con función de
Alto/Bajo/Apagado y con Bluetooth
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
Adjustments and Features
High Mode ..................................................0 V –10 V
Low Mode ............................................ 0 V – 9 V, Off
Time Delay .................... 30 seconds, 1 min – 30 min
Cut Off ............... Disable, 1 min – 59 min ,1 hr – 5 hr
Sensitivity ................ On-Fix, Off-Fix, Low, Med, High
Hold Off Setpoint ................ Auto, Disabled, 1–250 fc
Ramp Up ............................ Disabled, 1 sec – 60 sec
Fade Down ......................... Disabled, 1 sec – 60 sec
Photocell Setpoint for On/Off .......Disabled, 1–250 fc
Factory Defaults
High Mode .......................................................... 10 V
Low Mode ............................................................ 1 V
Time Delay ........................................................5 min
Cut Off ................................................................. 1 hr
Sensitivity .......................................................... High
Hold Off Setpoint .........................................Disabled
Ramp Up ......................................................Disabled
Fade Down ...................................................Disabled
Photocell Setpoint for On/Off .......................Disabled
Sensor Protection Cap
NOTE: Remove Cap before use
®
Reset Button
PIR Sensor
Motion Indicator
Blue LED
Light
Sensor