Operation Of The Tuner - Monacor PA-1140RCD Manual De Instrucciones

5.2 Operation of the tuner

Once a CD or a USB flash drive has been inserted,
the unit will automatically be switched to replay from
the CD or USB flash drive . Press the button MODE (3)
to switch between radio reception and replay from
the CD or USB flash drive .
5.2.1 Station tuning and storing
The tuner is able to receive FM and medium wave
stations . To allow storing of more than six stations
with the six station buttons (6, 7, 8, 14, 15), the FM
band has been divided into three identical subbands .
In each of the three subbands (F 1, F 2, F 3) and in the
medium wave band (MW), six stations can be stored
i . e . a total of 18 FM and 6 medium wave stations .
1) Select the desired band with the button BAND (4) .
It is recommended to store six stations in the band
F 1 first and then to switch over to the band F 2
and then to F 3 .
2) For station tuning, use either the automatic or
manual station scan:
To start the automatic station scan, briefly press
the button (11)
automatic station scan stops at the next station .
During the station scan, SEARCH is displayed . Re-
start the station scan repeatedly until the desired
station is received .
For manual station scan, keep the button
or pressed until MANUAL is briefly displayed .

Then the received frequency can be increased
or re duced step by step with each press of the
button (in the FM band by 50 kHz, in the medium
wave band by 9 kHz) . To run quickly through a
great range for manual station scan, keep the but-
ton or pressed . After manual station scan, the
 
unit switches to automatic station scan again after
a few seconds unless the button
pressed again before . AUTO is briefly displayed .
3) When the station has been tuned, keep the de-
sired numerical key (6, 7, 8, 14, 15) pressed until
the station number and "ch" appear on the right
in the display (see fig . 1) . Then the station is stored
under this number in the respective subband .
5.2.2 Calling up stored stations
1) Use the button BAND (4) to select the band in
which the desired station has been stored .
2) Select the number of the station with the corre-
sponding numerical key (6, 7, 8, 14, 15) .
3) Adjust the desired volume with the volume con-
trol LEVEL (17) .
4) With a stereo programme, ST appears on the top
left of the display .
12
(forward) or (backward) . The
 
or

5.2.3 RDS functions
If the selected station transmits RDS information
(radio data system), the name of the station is dis-
played instead of the frequency . Some stations show
additional information alternately with the station
name, e . g . music title, artist .
If a station offers traffic programme, TP is dis-
played . If EON (enhanced other networks) is shown
and a programme is received which currently does
not offer a traffic programme, the tuner automat-
ically switches to another programme of the same
broad casting station when traffic messages are
transmitted there . After the traffic announcement,
the unit switches back to the previous programme .
Information
With the button DISP (12), the following information
can be displayed:
1 press of button  time indication
st
If no time is transmitted, NO CLOCK is displayed .
The time is not transmitted continuously; there-
fore, it may take a few minutes until the time is
available after the radio has been switched on .
2 press of button  indication of the band (F1, F2,
nd
F3, MW) and of the station frequency
3 press of button  indication of the programme
rd
type
If no programme type is indicated by the station,

PTY NONE is displayed .
4 press of button  station name (basic setting)
th
The display switches to the basic setting after
5 seconds if no button is pressed .
This information can also be displayed with the
button DISP during the replay from a CD or USB
flash drive .
Alternative frequencies
has been

If AF is continuously displayed (not flashing), the pro-
gramme is also broadcast on alternative frequencies
of neighbouring stations . Then the unit automatically
changes to the station which can be received best .
With the button AF/ REG (9), this function can be
switched off (AF will be not be displayed any more)
and switched on again .
Some stations temporarily broadcast a different
programme depending on the region, e . g . regional
news . To make sure that the same regional pro-
gramme will be selected when the unit switches to
a station with better reception, the regional pro-
gramme mode can be switched on . Keep the but-
ton AF/ REG pressed for 3 seconds until REG ON is
briefly displayed . With the mode switched on, REG is
displayed . To switch off the mode, keep the button
AF/ REG pressed again for 3 seconds until REG OFF
is briefly displayed .