Publicidad
Idiomas disponibles
Idiomas disponibles
Check whether movable parts function perfectly and do
not stick or whether parts are damaged. All parts must be
correctly installed and fulfil all conditions to ensure perfect
operation.
Damaged safety devices and parts must be properly re-
paired or exchanged by a recognized, specialist work-
shop; insofar as nothing else is stated in the instructions
for use.
Damaged or illegible safety labels have to be replaced.
Do not allow any tool key to be plugged in!
Before switching on, checking always that all tools are re-
moved.
Store unused equipment in a dry, locked place out of the
reach of children.
Switch the machine off and remove the mains plug from the
socket when
Carrying out repair work.
Performing maintenance and cleaning
work.
Eliminating faults.
Checking of connection cables whether they are swal-
lowed or damaged
Storage and transport
Leaving unattended (even during short interruptions).
Do not carry out repair operations on the machine
other than those described in section "Maintenance"
but contact the manufacturer or authorized customer
service centres.
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer ser-
vice points.
Use only original spare parts and accessory parts.
Accidents can arise for the user through the use of
other spare parts. The manufacturer is not liable for
any damage or injury resulting from such action.
Electrical safety
Design of the connection cable according to IEC 60245 (H
07 RN-F) with a core cross-section of at least
2.5 mm² for a maximum cable length of up to 10 m
Never use the machine with a power supply cable of over 10
m in length. Longer power supply cables will cause a drop in
voltage. The motor will not be able to provide its maximum
performance and the operation of the machine will be im-
paired.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic mate-
rial of same mechanical stability or be covered with this ma-
terial.
The connector of the connection cable must be splash-proof.
When installing the power supply cable observe that it does
not interfere, is not squeezed, bended and the plug connec-
tion does not get wet.
Wind off completely the cable when using a cable drum.
14
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do not
use the cable to pull the plug from the socket.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables especial-
ly approved and appropriately labelled for outdoor use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
The electrical connection or repairs to electrical parts
of the machine must be carried out by a certified elec-
trician or one of our customer service points. Local
regulations
–
especially
measures – must be observed.
Description of device /
Spare parts
Please refer to the attached assembly and operating in-
struction sheet.
Pos.
Order no.
ASP 4 N-2
ASP 5 N-2
1
2
360348
3
359782
4
359783
5
359784
359796
6
359785
359797
7
359786
359789
8
359787
9
359789
359799
10
359788
11
359790
12
359792
359800
13
359791
14
359793
15
16
16A
17
18
19
20
360379
360349
21
22
23
24
25
360354
26
27
28
29
360350
30
359776
regarding
protective
Designation
Preassembled device
Carrying handle
Support brace
Support braces (pair)
Guard plate
Wood tray, rear
Wood tray, front
Front access guard
Rear wall, left
Rear wall, right
Lateral access guard
Upper access guard, left
Upper access guard, right
Connecting plate
Fastener bag
Operating instructions
Assembly and operating in-
struction sheet
Warranty declaration
Blade guard
Bleed screw
Dipstick
Operating pushbutton
Supporting foot
Cable
Motor
Wheel
Operating handle
Log ram
Piston rod
Oil seal
Safety label
Publicidad
Capítulos
