Maintenance And Care - Altrad ATIKA ASP 4 N-2 Manual De Instrucciones

Special instructions for splitting logs
Preparations:
The logs to be split should be cut to the maximum dimensions.
Ensure also that the logs are cut straight and square.
Place the log properly on the log splitter, so as not to cause
any risk of stumbling or falling to the operator.
Bleeding
Vent the hydraulic system before putting the log splitter into
operation.
 Open the bleed screw (19) 3 – 4 complete turns.
 Close the bleed screw again when you are finished splitting
logs.

If the hydraulic system is not vented, the trapped air will
damage the seals and cause permanent damage to the log
splitter.
Operating
Two-hand operation
1. Press the operating pushbutton (21) on the electric motor.
Wait a few moments until the motor has reached its operat-
ing revolutions and the required pressure has been built up
in the hydraulic pump.
2. Press the operating handle (26) first down and then
toward the front at the same time.

The log ram (27) pushes the log against the splitting
wedge, and the log will be split.
3. Release the operating lever as well as the operating
pushbutton. The log ram will now return to its original start-
ing position
Splitting logs
Always place the logs lengthwise and flat on the main

frame of the log splitter. The log must be enclosed by the
log guide plates.
Never place the log on the frame at an angle.

 Always ensure that the splitting wedge (18) and the log ram
(27) contact the ends of the log at right-angles.
 Never try to split two logs at once.
 Never try to remove or replace the log during the splitting
process.

Never try to force the splitting of the log by maintaining the
pressure for several seconds. This can lead to damage to the
machine.
Reposition the log on the main frame and repeat the splitting
process, or put the log to one side.
How to release a jammed log?
1. Loose the operating lever as well as the operating pushbut-
ton that the log ram can go back.
16
2. Place a triangular wooden chock under the log,
then move the log ram forward so that it pushes the chock
under the jammed log.
3. If the log is not released, keep repeating this procedure,
using larger chocks, until the log is released.
Never use a hammer to release a jammed log, and
keep your hands away from the log.
Do not enlist the aid of a second person - this is a one-man job.
Do not try to release the log by using a hammer, since
this may break the motor block.
Finishing work
 Attend to that the log ram has gone back to its basic posi-
tion.
 Then remove the plug from the power socket.
 Close the bleed screw (19).
 Follow the care and maintenance instructions.

Maintenance and care

Remove the plug from the power socket before start-
ing any maintenance or cleaning work.
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Only use genuine spare parts. Other than genuine parts may
result in unpredictable damages and injury.
Wear protective gloves in order to avoid injury to the
hands.

Observe the following in order to keep the log splitter in
good working order:
 Clean the machine thoroughly after you have finished
using it.
 Remove any resin remains on the machine.
 Oil the piston rod (28) regularly with an environmental-
ly friendly spray oil.
 Check the oil level and change the oil as necessary.
Sharpening the splitting wedge

After extended periods of use, or if the splitting perfor-
mance is reduced, sharpen the splitting wedge (18) with a
file (and remove any burrs).
How do I check the oil level?
1. The log ram (27) must be in its starting position.
2. Stand the log splitter on end, with the filler opening at the
top.
A second person will be required to up-end and
hold the log splitter.
3. Unscrew the dipstick (20) . Do not drop or lose the oil
seal (23) when removing the dipstick.