Max ERZ-300 Manual De Instrucciones página 6

■
If paper is scratched by staples
①
Dispose of staples remaining in the waste box.
● NOTE: See "Procedure for waste staple disposal".
②
Visually check for staples remaining in the machine.
③
If there are staples remaining, operate the machine empty a few
times by pressing the button with no paper inserted.
④
If staples still remain in the machine, insert some paper you do
not need and perform step
⑤
Pull out the waste box and place the machine vertically as
shown in the diagram.
⑥ Use tweezers or the like to remove remaining staples.
● CAUTION: Do not grip staples with your bare hands. Doing so may
lead to injury.
■
If paper jams occur repeatedly
①
Follow the procedure to remove the paper.
● NOTE: See "Procedure for clearing paper jams".
②
Check for staples remaining in the machine. Follow the procedure
to remove staples if they remain.
● NOTE: See "If paper is scratched by staples".
8. Specifications
Product name
Model name
Number of sheets staples can be removed from
Staple types
External dimensions
Weight
Manufacturer's name or trade mark
Address
Importer Name In Europe
Importer Address In Europe
Importer Name In USA
Importer Address In USA
Power consumption
Power source
Working Temp. and Humidity ranges
■
AC ADAPTER INFORMATION
Manufacturer's name
Commercial registration number and address
Model identifier
Input voltage
Input AC frequency
Output voltage
Output current
Output power
Average active efficiency
Efficiency at low load (10 %)
No-load power consumption
● Removal capacity noted in the product specifications is when using 80g/
of paper or staples or the temperature/humidity environment, removal according to specifications may not be
possible. In that case, do not attempt to use the product.
● If using for a long time continuously, the motor may overheat and staple removal not be possible. In that case,
stop using the machine for a while and let the motor cool off before using again.
● Use for removing 26/6 staples from 30 or fewer sheets of 80g/
cause malfunction.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
• AC adaptor with ferrite core must be used for RF interference suppression.
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
③ ⑤
. Then, try step
COMMISSION REGULATION (EU) 2019/1782 of 1 October 2019
FCC WARNING
.
Electric Staple Remover
ERZ-300
Up to 30 sheets (80 gsm, No.35(26/6))
24/6, 26/6, 10, copier finisher staples
126 (W) x 273 (D) x 105 (H) mm
2 kg
MAX CO., LTD.
6-6 Nihonbashi Hakozaki-cho, Chuo-ku, Tokyo, Japan
MAX EUROPE B.V.
Antennestraat 45, 1322AH, Almere, The Netherlands
MAX USA CORP.
205 Express Street Plainview, New York 11803, U.S.A.
Approx. 60W, 2.5A
DC24V, 2.5A
Use only specified AC adapter (AC 100-240V, 50-60Hz)
appended to machine.
10°C /50°F -35°C /95°F, Below 80% RH (non-condensation)
MAX CO., LTD.
0100-01-057739
6-6 Nihonbashi Hakozaki-cho, Chuo-ku, Tokyo, Japan
6A-601DA24
AC100-240V
50-60Hz
DC24.0V
2.7A
64.8W
88.0%
79.0%
0.21W
m
PPC paper. Depending on the type
m
PPC paper. Using in excess of the capacity will
FCC Notice (Class B: ERZ-300)
CAN ICES-3 (B) / NMB-3 (B)
5
⑤
⑥
②