Eurosystems MFL01 Instrucciones De Uso página 21

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

ASSEMBLY CABLE FOR BAR CONNECTION (Fig.15)
n
you need to make the cable to pass into the nib place on the side of the frame. Make the cable to pass into the steel ring of the handlebar support
(fig.13 part.7) and into the nib hole (2) then into the red lever ( 4).
CUTTING BLADE ASSEMBLY+ BAR MOUVEMENT (Fig. 4-4A-7)
n
assembly the protection part you can find inside the packaging box. For protection safety purposes, please always wear a pair of hardy gauntlets. To
make the assembly of the cutting blade (A fig.7) device to the unit (B fig. 7) easier we recommend you to perform the work on a work bench. Fig. 4)
The cutting mower is equipped with a joint which allow the easy quick connection of the cutting set to the unit. The engine has to be switched off and
the unit put in horizontal position: grease the bar pin with engine oil (1) and insert it all the way into its seat (2).
Assemble the belt (3) on the pulley, then on the cutting bar. Assembly the grass separating cover (6) and fix it on the front antivibrating part (8) then
on the welded screw (7). Put the washer (10) on the screw and screw it with the nut (12).
Fig. 4A) Position 1 and 2 : turn the handle (13) until you are able to couple the right side spring (14) to the connection (15) . Position 2 and 3 : to
complete the above coupling, rotate the handle (13) in the opposite direction until you are able to tension the spring (14).
STARTING UP (Fig. 5)
n
The tank has a capacity for about 0,500 kg. and has to be filled in up to the shown level. Anyhow, please always read very carefully the enclosed
instruction referring to engine. Put the throttle handle (1) on start position , then switch the engine on. Adjust the handle in order to get to the needed
engine revolutions.
In order to connect the cutting bar it is sufficient to rotate the safety catch (3) to the top and to lower the lever (4). When the lever (4) is released. the
bar stops.
In order to engage the forward speed it is sufficient to turn down the safety catch (5) and pull the lever (1). When the lever is released (1) the machine
stops.
In case you have to face an unforeseen and accidental obstacle, you should immediately leave the two driving levers (2 and 3). When you finished
your work, please switch the engine off, and put the throttle handle (1) on stop position.
n
ADJUSTING AND CONNECTION FOR THE SCYTHING BAR (Fig.5)
accessories, you should act on the adjusters (2) to make the bar to start scything only when the red lever (4) has crossed half its way. ATTENTION :
before lowering the accessories insert red lever (4), you should always unhook the safety lever (4).
n
BELT- STRETCHER CONTROL ADJUSTMENT (Fig.6)
lever ( fig.5 part.1) has crossed half its way. When the mentioned lever is completely pulled, on working position , the belt-stretcher load spring (2)
should extend between 6-8 mm. To obtain the am conditions you have to act on the nut (1) set close near the belt-stretcher control.
n
ADJUSTMEN OF THC SCYTHING BAR HEIGHT (Fig.7)
scything bar height. Please follow the instruction: loosen the nut (1), bring the plastic strip (2) to the needed position and tighten the nut. Please
perform the operation on both the plastic strips.
ATTENTION!: the scythe mower is delivered with a 4 stroke engine: oil is not included.
the cable is already linked to the black level placed under the frame and
ATTENTION ! before handling the cutting bar please
To increase the belt tension between the unit and the
Attention : the motor-mower wheels should start to turn when the driving
If you need to scythe on uneven grounds it is necessary to adjust the
EN
21

Publicidad

Tabla de contenido
loading

Tabla de contenido