Bestway 2621064 El Manual Del Propietario página 2

137 cm (54 in) above the threshold of the door.
(b) The pool should be equipped with a power safety cover which
complies with ASTM F1346-91 listed below.
(c) Other means of protection, such as self-closing doors with
self-latching devices, are acceptable so long as the degree of
protection afforded is not less than the protection afforded by
(a) or (b) described above.
10. Where an aboveground pool structure is used as a barrier or where
the barrier is mounted on top of the pool structure, and the means
of access is a ladder or steps, then (a) the ladder to the pool or
steps should be capable of being secured, locked or removed to
prevent access, or (b) the ladder or steps should be surrounded by
a barrier which meets Section I, Paragraphs 1 through 9. When the
ladder or steps are secured, locked, or removed, any opening
created should not allow the passage of a 10 cm (4 in) diameter
sphere.
Section II: Barrier Locations
Barriers should be located so as to prohibit permanent structures,
equipment or similar objects from being used to climb the barriers.
Item Number: 2621064
Installation usually takes approximately 10 minutes with 2-3 people
excluding earthworks and filling.
Pool liner
Drain Valve Cap
Preparation
Do not install the pool on a slope or inclined surfaces, on soft or loose
soil conditions (such as sand or mud), or on an elevated surface such
as a deck, platform or balcony, which may collapse under the weight of
the filled pool.
• It is essential the pool is set up on solid, level ground. If the pool is
set up on uneven ground it can cause collapse of the pool and
flooding, causing serious personal injury and/or damage to personal
property. Setting up on uneven ground will void the warranty and
service claims.
• Do not set up on driveways, decks, platforms, gravel or asphalt.
Ground should be firm enough to withstand the pressure of the water;
mud, sand, soft / loose soil or tar are not suitable.
• The ground must be cleared of all objects and debris including stones
and twigs.
• Check with your local city council for by-laws relating to fencing,
barriers, lighting and safety requirements and ensure you comply with
all laws.
Installation
Assembly can be completed without tools. (air pump not included)
NOTE: It is important to assemble pool in the order shown below. Adult
assembly required.
1. Find solid, level ground and clear it of debris.
Attention: Do not set up the pool under cables or under trees.
2. Spread out the pool and make sure it is right side up.
3. Cover the water valve.
4. Inflate the top ring and close the air valve after inflation.
Note: Do not over inflate. Over inflation may cause damage.
5. Put 2.5 to 5 cm (1 in to 2 in) of water in the pool to the cover the floor. Once
pool floor is slightly covered, gently smooth out all wrinkles. Start in the
center of the pool and work your way clockwise to the outside.
6. Continue to fill the water to the filled line. Please kindly pay the utmost
attention not over fill the pool for security reasons.
NOTE: Connect a garden hose to the adapter located on the inflatable top
ring to activate the water sprayers (tentacles).
NOTE: When water sprayers (tentacles) are engaged, please open the valve
located on the upper outside wall to drain excess water. This will prevent
overflow and allow the pool to maintain it's structure. When water sprayers
are not active, close the valve to prevent water from draining.
Please see FAQ's for additional information.
x1
Hose Adaptor
x1
Underwater adhesive repair patch
Water Valve
NOTE:
Drawings for illustration purposes only. May not reflect
actual product. Not to scale.
ATTENTION:
Do not leave pool unattended while filling with
water.
x1
Pool walls will rise as you fill with water.
1. Fill pool until water capacity is 80%, DO NOT OVERFILL as this
could cause the pool to collapse. In times of heavy rainfall you may
need to empty some of the water to ensure the level is correct.
2. When filling the pool is completed, check that the water is not
collecting on any side to ensure the pool is level.
x2
Dismantling
1. Unscrew the drain valve cap counter-clockwise and remove.
2. Connect the adaptor to the hose and put the other end of the hose
in the area where you are going to drain your pool. (Check local
regulations for drainage by-laws).
3. Screw the control ring of the hose adaptor clockwise onto the drain
valve. The drain valve will be open and water will start to drain
automatically. Open the drain valve to the maximum position.
4. Deflate the top ring by squeezing the air valve.
5. When the top ring is fully deflated, press the top ring down, and tilt it
to drain the pool easily. Completely drain the water in the pool.
6. When draining is finished, unscrew the control ring to close the
valve.
7. Disconnect the hose.
8. Screw the cap back onto the drain valve.
9. Air dry pool.
Note:
Drain by adult only!
ATTENTION:
Do not leave the drained pool outside.
Repair
If your pool is damaged, use the provided repair patch.
1. Clean area to be repaired.
2. Carefully peel patch.
3. Press patch over area to be repaired.
4. Wait 30 minutes before inflation.
Pool Maintenance
If you do not adhere to the maintenance guidelines below, your health
might be at risk, especially that of your children.
Using chemical tablets (not included):
NOTE:
Chemconnect or Chemical Floater must be used when you
perform chemical maintenance with tablets. Your purchased item may
not include any of those dispensers, in this case you can purchase it
by visiting our website www.bestwaycorp.com or at the nearest pool
dealer.
2
Only one dolphin has the
built-in water sprayer, the
other two dolphins do not
Filled Line
have water sprayer.
Hose
Connector
0°