Stanley FAT MAX FMHT1-77413 Manual Del Usuario página 7

5. Slide the Power/Transport Lock switch to the right to the
Unlocked/ON position (Figure
6. On the keypad (Figure
(> 25%). If is red, this means that the battery level is
below 25%.
• The laser may continue to operate for a short time while
the battery power continues to drain, but the laser dots
will quickly dim.
• After fresh batteries are installed and the laser is turned
ON again, the laser dots will return to full brightness.
7.
When the laser is not in use, slide the Power/Transport
Lock switch to the LEFT to the Locked/OFF position (Figure
#1a) to save battery power.
A
Using the Mounting Block
On the bottom of the laser is a moveable block (Figure
• To use the magnets on the front of the laser (Figure
mount the laser against the side of a steel beam, do not
extend the moveable block (Figure
down dot to be aligned with the edge of the steel beam.
• To mount the laser over a point on the floor (using a multi-
function bracket or a tripod), pull out the moveable block until
it clicks in place (Figure
D
dot to display through the 5/8-11 mounting hole and the laser
to be rotated over the 5/8-11 mounting hole without moving
the vertical position of the laser.
Turning the Laser On
1. Place the laser on a smooth, flat, level surface.
2. Slide the Power/Transport Lock switch to the right to the
Unlocked/ON position (Figure
3.
As shown in Figure #3a, press
A
dots (above, ahead, and below the laser), and a second time
to display 2 additional dots to the right and left of the laser.
4.
Check the laser beams. The laser is designed to self-level.
If the laser is tilted so much that it cannot self-level (> 4°),
the laser beams will continually flash twice and
constantly on the keypad (Figure
5. If the laser beams flash, the laser is not level (or plumb) and
should NOT BE USED for determining or marking level or
plumb. Try repositioning the laser on a level surface.
#1b).
A
#3b), make sure is green
A
D
A
#1). This will allow the
D
#2). This will allow the laser down
#1b).
A
once to display 3
will flash
#3c).
A
6. If ANY of the following statements are TRUE, continue with
the instructions for Checking Laser Accuracy BEFORE
USING THE LASER for a project.
• This is the first time you are using the laser (in case the
laser was exposed to extreme temperatures).
• The laser has not been checked for accuracy in a while.
• The laser may have been dropped.
Checking Laser Accuracy
The laser tools are sealed and calibrated at the factory. It
is recommended that you perform an accuracy check prior
to using the laser for the first time (in case the laser was
exposed to extreme temperatures) and then regularly to ensure
the accuracy of your work. When performing any of the
accuracy checks listed in this manual, follow these guidelines:
• Use the largest area/distance possible, closest to the
).
operating distance. The greater the area/distance, the easier
#2) to
to measure the accuracy of the laser.
• Place the laser on a smooth, flat, stable surface that is level
in both directions.
• Mark the center of the laser beam.
Plumb Dot Accuracy
Checking the plumb calibration of the laser can be most
accurately done when there is a substantial amount of vertical
height available, ideally 25' (7.5 m), with one person on the floor
positioning the laser and another person near a ceiling to mark
the dot created by the beam on the ceiling.
1.
Mark point P1 on the floor (Figure
2.
Turn the laser ON and press
above, ahead, and below the laser.
3.
Place the laser so that the down dot is centered over point
P1 and mark the center of the up dot on the ceiling as point
P2 (Figure #1).
F
4.
Turn the laser 180°, making sure that the down dot is still
centered on point P1 on the floor (Figure
5. Mark the center of the up dot on the ceiling as point P3
(Figure #2).
F
6. Measure the distance between points P2 and P3.
#1).
F
once to display dots
#2).
F
GB
7