Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
MODES
Speed is shown on-screen at all times.
Its maximum reading is 99.9km/h(m/h)
and is accurate to +/-0.1km/h (m/h).
Odometer - In ODO mode, the total
distance is indicated onscreen. The
mileage range is 0.001-99999km(m).
The display will return to 0 when the
value exceeds its maximum limit. Press RIGHT
button to enter DST mode.
Trip Distance (DST) - In DST mode,
the distance for one trip is indicated
on the bottom line. DST ranges from
0~9999km(m). When trip distance
exceeds the range limit, it resets to 0 automatically.
Both the time and the distance records will be
cleared when the time of one trip exceed the range
limits. Press the LEFT button for 5 seconds to clear
the records of DST, MXS, AVS and TM. Press the
RIGHT button to enter MXS mode.
Maximum Speed (MXS) - In MXS mode,
maximum speed is indicated on the
bottom line. Press the LEFT button for 5
seconds to clear the records of MXS,
DST, AVS and TM. Press the RIGHT button to
enter AVS mode.
Average Speed (AVS) - In AVS mode,
average speed is indicated on the bottom
line. Press the LEFT button for 5 seconds
to clear the records of AVS, DST, MXS and
TM. Press the RIGHT button to enter TM mode.
Trip Time (TM) - In TM mode, trip time is
indicated on the bottom line. TM ranges
from 0:00:00 to 99:59:59 and will be
reset to 0 when the value exceed the limit. Press the
LEFT button for 5 seconds to clear the records of
AVS, DST, MXS and TM. Press the RIGHT button to
enter SCAN mode.
Scan - In SCAN mode, DST, MXS, AVS and
TM modes are indicated in turn every 4
seconds. Press the RIGHT button to enter
CLOCK Mode.
TROUBLESHOOTING
Malfunction
No speedometer reading
Inaccurate value is indicated
Slow display response
Black display
Weak or faint display
Display shows irregular gures
Problem
Incorrect magnet/sensor alignment
Improper input, such as wheel circumference
Temperature exceeds operating limits (0˚C~55˚C)
Temperature too high, or placed in direct sunlight
Poor battery contact or dead battery
Poor battery contact
ADDITIONAL FEATURES
Sleep Mode - If no signal has been received for 5
minutes, the computer will enter into Sleep Mode.
The CLK value remains stored. It will turn back to
the previous mode with all the data collected when
a signal is received again or any button is pressed.
Pace - During riding, '+'and '-' indicates the current
speed is higher or lower than the average speed (AVS).
Resetting the Odometer – If you are re-installing or
replacing the battery, take a note of your mileage and you
can re-enter the value once the battery is in place. To do
so, in ODO mode, press the LEFT button for 2 seconds to
set the ODO value. The initial value is 0000.0. when one
gure ashes, press the RIGHT button to adjust it, and the
LEFT button to con rm and start to set the next gure.
Resetting Wheel Diameter - In ODO mode, press and hold
both the RIGHT and LEFT buttons simultaneously for 3
seconds to clear the tire circumference and (km/m)
settings. The clock settings will remain unchanged.
Freeze Frame Memory - Press the LEFT button at any time
to enter Freeze Frame Memory mode. Flashing TM data
will appear on the screen. Press the RIGHT button to view
the records of DST, MXS, AVS and TM. Press the LEFT
button to cancel.
Button Instruction - Press the RIGHT button to choose
any of these modes: ODO, DST, MXS, AVS, TM, SCAN
(DST, MXS, AVS & TM) and CLOCK. It is not necessary to
press the LEFT button except to select the Freeze frame
Memory mode. In Freeze Frame Memory mode, press
the RIGHT button, data will be displayed, press LEFT
button once more to return to other modes.
Resolution
Con rm correct alignment of sensor and magnet
Con rm or re-input wheel circumference
Cover and allow to cool down
Cover and allow to cool down
Replace battery
Take out battery and re-install after 10 seconds
Publicidad
Tabla de contenido
