Publicidad
INSTRUCTION GUIDE
Wireless Chime Buttons RC3302, RC3303, RC4121
Congratulations on a wise purchase!
ENCLOSED YOU WILL FIND:
• Chime Button
• One 3-volt lithium battery (installed) for RC3302 and RC3303
• Two 3-volt lithium batteries (installed) for RC4121
• Double-sided tape
• Screws
TOOLS NEEDED:
• Small Phillips head screwdriver
• Medium flat head screwdriver
• Ballpoint pen
• Drill, if mounting with screws
Note: Your new wireless chime button can only be used to add
a button to an existing Carlon Wireless Chime system. It can not
be used with any other mechanical or wireless chime system.
MOUNTING BACK COVER OF CHIME BUTTON
Note: Mounting Chime Button on aluminum siding or metal door
frame may reduce range. If button must be mounted on metal,
try placing a 1/2'' piece of wood between the button and the
metal.
If you want to cover the wire hole from your existing button, save
mounting of the new Chime Button until after removing the
existing button.
1. Remove cover from back of Button by inserting flat head
screwdriver in notch at bottom of transmitter and turn. Lift
Chime Button cover away from the back plate.
2. For tape mounting:
A) Make sure surfaces are free of dust, oil, and other
substances that could affect adhesion.
B) Attach double-sided tape to Chime Button back cover.
C) Making sure that the end with the hook-shaped latch is
facing down, press cover firmly to mounting surface.
3. For screw mounting:
A) Place Chime Button where desired and mark screw
locations.
B) Place Chime Button back cover against mounting surface
and screw into marked locations using screws enclosed
(may require drilling pilot holes on hardwoods).
4. Reattach the Chime Button to the installed back cover.
TEST
Press Chime Button. Receiver should play tone.
CHANGING TONE/MELODY SELECTION
To change to a different tone or melody,
press once on the small raised Button
located on the bottom front of the
Button. Receiver will play next selection.
To continue changing melody or
selection, press down once again and
wait for Receiver to confirm change.
Note: If you change melodies or tones
too rapidly, the Receiver will not play
each selection. Only last melody or tone
selected will play. Selecting while
Receiver is playing will switch system to new
setting, but Receiver will only finish playing tone
or melody already in progress.
FRONT/BACK DOOR CHIME OPERATION
With two Chime Buttons, scroll and set a different selection for
each door. By remembering which tone/melody is played, you
can tell which button is pressed. Chime Buttons may also be
used as hand-held pagers.
TO REPLACE BATTERIES
1. Remove Chime Button from back
cover by inserting flat head
screwdriver in notch at bottom of
Button and turn. Lift Chime Button
cover away from the back plate.
2. Remove old battery(s) by placing a
ballpoint pen directly beneath the
battery(s). For RC4121, lift the top
battery out of the battery
compartment. Repeat with second
battery. (Do not hit Chime Button to
remove batteries - this could
damage the Button.) Dispose of
used battery(s) promptly. Keep
away from children. Do not
Press to
disassemble and do not dispose
change
of in fire.
tone or
3. Replace old battery(s) with new
melody
battery(s), positive (+) side up.
BATTERY CAUTION – Do not
recharge, disassemble, heat above
100ºC (212ºF), or incinerate. Replace
only with UL approved Type CR2032
3 volt lithium batteries, such as,
RC3303
Carlon RC3395D. Use of another
battery may cause failure of the transmitter and will void
manufacturer's warranty and liability.
TROUBLESHOOTING TIPS
PROBLEM: Receiver does not sound when button is pressed.
SUGGESTION: Verify that Button battery(s) is installed correctly
and battery contacts are in the correct position. Try replacing
Button battery(s) first. Make sure outlet is functioning. Check that
Receiver and Button are placed within operating range.
RC3302
Transmitter
button
Back
cover
Publicidad
