Tabla de contenido
Publicidad
2. Loosen the depth-adjusting knob in the direction of
the unlocking arrow marked on the knob (Fig. C).
3. Move the guide wheel, along
guide bar, up to increase the depth of cut or down to
decrease the depth (Fig. D).
4. Adjust the guide wheel so that the blade just touches
the ground or breaks the surface of the soil by no
more than 5mm (Fig. E) and then tighten it securely.
5. Standing in the normal working position, check the
depth of cut again and correct it if necessary.
TO START/STOP THE TOOL
See "STARTING/STOPPING THE POWER HEAD" section
in the power head PH1400E operator's manual.
OPERATING TIPS
◾
Hold and guide the power head so that the blade is
vertical. Use the sight line to line the blade up with the
edge of the bed (Fig. F).
◾
Operate at no more than a normal walking pace. If the
blade begins to bog down, you are edging too fast;
slow your pace.
◾
Always walk forwards when cutting and move the
edger forward. Do not pull the edger towards you.
◾
Do not force the blade into the ground. Light contact
of the blade against the sidewalk edge, curb, etc., is
acceptable and will not damage the edger.
◾
Best results are obtained when grass is dry. Avoid
edging in wet soil or wet grass areas or the blade
guard might clog and result in an uneven edge. If the
blade guard becomes clogged, stop the motor, remove
the battery pack, and remove debris from the blade
guard.
MAINTENANCE
WARNING:
Before inspecting, cleaning or servicing
the unit, stop the motor, wait for all moving parts to stop,
and remove the battery pack. Failure to follow these
instructions can result in serious personal injury or
property damage.
WARNING:
When servicing, use only identical
replacement parts. Use of any other parts can create a
hazard or cause product damage. To ensure safety and
reliability, all repairs, other than the items listed in these
maintenance instructions, should be performed by a qualified
service technician.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
the depth-adjusting
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
CLEAN THE UNIT
◾
After each use, clean the debris, clogged soils or grass
on the blade and guard with a soft brush. Wipe the
edger surface with a clean cloth moistened with a mild
soap solution.
◾
Use a small brush or a small vacuum cleaner to clean the
air vents on the rear housing.
NOTICE:
housing or the handle. They can be damaged by certain
aromatic oils such as pine and lemon.
REPLACING THE BLADE
bent or cracked blade-it may break-it must be replaced.
Recommend replace only with EGO edger blade, see
"Recommended Blade" section.
NOTICE:
sufficient to maintain the necessary ground clearance and
obtain the required depth of cut.
heavy gloves or wrapping the blade with rags or other
materials when performing any maintenance on the edger
blade.
Removing the blade
1. Stop the motor and remove the battery pack.
2. Lay the edger on its back so that the blade is facing
3. Wear protective gloves. Use a needle nose pliers (not
4. Rotate the blade to align the slot in the flange with
5. Insert the hex wrench provided into the aligned holes
Do not use any strong detergents on the plastic
WARNING:
Do not attempt to straighten or weld a
Replace the blade if its length is no longer
WARNING:
Always protect your hands by wearing
upwards.
included) to remove the cotter pin from the motor
shaft (Fig. G).
the hole in the
gear case (Fig. G).
Fig. G parts description see below:
G-1
Cotter Pin
G-2
Inner Flange
G-3
Gear Case
to act as a stabilizer. Use the multi-functional wrench
provided to loosen the nut CLOCKWISE (Fig. H).
EDGER ATTACHMENT — EA0800
EN
9
Publicidad
Tabla de contenido
