Cleaning And Maintenance; Storage And Transportation - Redmond RHB-2908-E Manual Del Usuario

2. Connect the blending attachment to the motor unit and turn counterclockwise
until it clicks into place.
3. Plug in the appliance. Select the required speed setting.
4. Hold the vessel steady and place blending attachment in the food. Press and hold
down the Power button. When processing raw vegetables, fruits, and other hard
foods turn the speed control knob to increase the speed or press and hold down
the Turbo mode button.
5. Blend foods using circular up-and-down motion.
6. After use unplug the appliance. Turn the blending attachment clockwise to discon-
nect from the motor unit. Clean the appliance following the procedure outlined
in "Cleaning and Maintenance" section.
To Operate the Whisk
1. Fill the beaker or a similar vessel with food.
2. Insert the whisk attachment to the gear box until it clicks into place.
3. Connect the gear box to the motor unit and turn counterclockwise until it clicks
into place.
4. Plug in the appliance. Turn speed control knob clockwise to setting 1 (minimum
speed).
5. Hold the vessel steady and place whisk attachment in food. Press and hold down
the Power button. Turn the speed control knob counterclockwise to increase the
speed if necessary (from 1 to 5). To whisk at a maximum speed press and hold
down the Turbo mode button.
6. Whisk foods using clockwise circular motion.
7. After use unplug the appliance. Disconnect the attachment and the gear box from
the motor unit by turning clockwise. Clean the appliance following the procedure
outlined in "Cleaning and Maintenance" section.
To Operate the Chopper
1. Place the chopper bowl on a flat and stable surface.
2. Remove the protective plastic cover from the chopper blade. Fit the blade on the
central pin at the bottom of the chopper bowl. Note: the blade is very sharp, handle
with caution! Always hold the blade by the plastic collar.
3. Fill the bowl with food. Do not fill above the maximum fill mark (500 ml).
4. Fit the lid onto the bowl, aligning the crosspiece of the plastic collar with the
corresponding notches in the center of the lid. Gently press the lid down and
rotate clockwise.
5. Connect the motor unit with the chopper gear box until it clicks into place.
6. Plug in the appliance. Select the speed setting: harder foods require higher
chopping speed.
7. Holding the bowl with one hand press and hold down the Power button or
TURBO mode button. Use TURBO mode to chop meat and other hard foods.
Maximum continuous operation time must not exceed 1 minute.
8. After use unplug the appliance. Press release buttons on the motor unit and
disconnect the motor part. Twist the lid counterclockwise to remove. Remove the
blade, holding it by the plastic collar.
9. Clean the blade and put protective plastic cover back on.
III. CLEANING AND MAINTENANCE
Wipe the motor unit with soft damp cloth.
DO NOT immerse in water or wash the motor unit under running water.
Wash the removable parts in warm soapy water. Mix water with lemon juice to add
extra shine to metal parts of the appliance. Exercise caution when cleaning the blades,
they are extremely sharp. Rinse the blades under hot running water.
DO NOT use a sponge or tissue with hard or abrasive surface or abrasive pastes. Do
not use any chemically aggressive substances or any other agents which are not recom-
mended for cleaning items that come into contact with food.
Let all parts of the appliance dry thoroughly before use.
Some foods (such as carrot and beet) may stain the plastic. Apply bleach-based solution
immediately after use to remove the stains.

Storage and transportation

Before repeated operation or storage completely dry all parts of the appliance. Store
the assembled appliance in a dry, ventilated place away from heating appliances and
direct sunlight.
During transportation and storage, do not expose the device to mechanical stress, that
may lead to damage of the device and/or violation of the package integrity.
Keep the device package away from water and other liquids.
RHB-2908-E
GBR
7