Description Of Symbols; General Safety - Silverline 427558 Manual Del Usuario

GB

Description of Symbols

The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction Manual.
DO NOT use with compressed gas cylinders!
Conforms to relevant legislation and safety standards
Environmental Protection
Air tools should not be disposed of with household waste. They
contain traces of oil and other lubricants. Please recycle where
facilities exist. Check with your local authority or retailer for recycling
advice.
Specification
Operating pressure range: .....................2.0-6.3bar
Air consumption: ..................................approx. 113L/min
Air inlet: ................................................¼" BSP, supplied
with two male airline quick connectors (EN-6 'UK' and EQ-4
'European' types)
Minimum hose diameter: .....................9.5mm (3/8")
Capacity:...............................................400cm
Grease outlet pressure: ........................approx. 60-190bar
Chamber length: ...................................280mm
Net weight: ...........................................1.45kg
As part of our ongoing product development, specifications of
Silverline products may alter without notice.
4
(30-90psi)
(4cfm) at 6.3bar
(90psi)
(Bulk)
3
(900-2700psi)

General Safety

• For multiple hazards, read and understand the safety instructions before
installing, operating, repairing, maintaining, changing accessories on, or working
near this tool. Failure to do so can result in serious bodily injury
• Only qualified and trained operators should install, adjust, or use this tool
• Do not modify this tool. Modifications can reduce the effectiveness of safety
measures and increase the risks to the operator
• Do not discard the safety instructions; give them to the operator
• Do not use this tool if it has been damaged
• Tools shall be inspected periodically to verify that the ratings and markings
required by this part of ISO 11148 are legibly marked on the tool. The employer/
user should contact the manufacturer to obtain replacement marking labels
when necessary
WARNING: This appliance is not intended for use by persons (including children)
with reduced, physical or mental capabilities or lack of experience or knowledge
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Children must be supervised to
ensure that they do not play with the appliance.
Projectile hazards
• Be aware that failure of the workpiece or accessories, or even of the inserted
tool itself, can generate high-velocity projectiles
• Always wear impact-resistant eye protection during operation of this tool. The
grade of protection required should be assessed for each use
• For overhead work, wear a safety helmet
• The risks to others should also be assessed at this time
• Ensure that the workpiece is securely fixed
Operating hazards
• Use of the tool can expose the operator's hands to hazards, including cuts,
abrasions and heat
• Wear suitable gloves to protect hands
• Operators and maintenance personnel should be physically able to handle the
bulk, weight and power of the tool
• Hold the tool correctly; be ready to counteract normal or sudden movements
and have both hands available
• Maintain a balanced body position and secure footing
• Release the start-and-stop device in the case of an interruption of the energy
supply
• Use only lubricants recommended by the manufacturer
• Personal protective safety glasses should be used; suitable gloves and
protective clothing are recommended
• Inspect the spouts before each use. Do not use if cracked or broken or if it has
been dropped
• There is a risk of electrostatic discharge if used on plastic and other non-
conductive materials
Repetitive motions hazards
• When using this tool to perform work-related activities, the operator can
experience discomfort in the hands, arms, shoulders, neck or other parts of
the body
• While using this tool, the operator should adopt a comfortable posture whilst
maintaining secure footing and avoiding awkward or off-balance postures. The
operator should change posture during extended tasks; this can help avoid
discomfort and fatigue
• If the operator experiences symptoms such as persistent or recurring
discomfort, pain, throbbing, aching, tingling, numbness, burning sensations or
stiffness, these warning signs should not be ignored. The operator should inform
the employer and consult a qualified health professional
Accessory hazards
• Disconnect the tool from the energy supply before fitting or changing the
inserted tool or accessory
• Use only sizes and types of accessories and consumables that are
recommended by the manufacturer of this tool; do not use other types or sizes
of accessories or consumables